完整一套产品检测标准(英文)Word文档

MTL SGS TEST LIST (1)
(Seating)
(Combines Adult and Children’s sizes,:Chairs, Barstools, Ottomans,)
Quality test standardmethod
ng DesignFeatures（标签设计
特点）
ctions指示 说明
Criteria（标准）
The actuality must keep consistency（一致性） with the claim（要
求）.
Shall be included if necessary. Shall include assembly, mounting
（装备）, use, maintenance（维护）, cleaning and safety information
as required in the language(s) applicable to the destination（目的
地） country(s) with no errors or spelling mistakes.（地名写错）
Shall be easy to follow and accurate.
t sizeweight产品尺寸 重量
Statement
Report actual. Shall comply with any claims (-0%, +3%)
inches or greater are used in inner packaging, the following
warning statement must be printed on at least one side of each bag
in English, French and Spanish:
5. Lead In Surface Coating（被复盖）
6. Workmanship（工艺） Level
Shall not exceed 600 ppm (0.06% by weight) total lead
?
?
?
?
?
?
?
?
?
No major defects（缺点）。
No components（成分） missing, malformed（畸形的） or
fractured （破裂）
No hardware missing
Smoothly ground welds（接合）, not over-ground and free
of pits（凹陷） and splatter（说话结巴）
No burrs（喉音）
No loose components and unsecured fastening where
rigidity（硬度） is required
In the case of wood (e.g. laminates（薄板) proper and
uniform（一致的） adhesion（支撑）
No scratches, dents（凹痕）, cracks（裂缝）, marred（损
坏） or discolored surface
In the case of molded plastic, consistent and concise form
and no defects evidencing（明显的） of overuse（过度的）
of mold。
?
?
?
?
?
?
7. Sharp Points and Edges
8. Cross Cut Adhesion
Finished edges and seams（衔接口）
Accurate and consistent（调和的） painting
Components even in color, uniform clarity
All seams and components in even alignment（结盟）
Accurate and consistent painting
Components even in color, uniform clarity（清楚）





Results

4. Costco Plastic Bag Warning If plastic bags (of any thickness) with a perimeter(周长) of 14
Shall have no sharp edges or sharp points on any component other
than those required for functional use.
Plating finish must stay affixed – using a utility（万能）knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to the
grid. Remove to see if plating finish remains intact.（完整无缺）
9. Flammability（可燃性） of Upholstery Must comply with California Bureau of Home Furnishings Bulletin

Materials
10. Finger Entrapment
116117

Shall meet the requirements intended to eliminate （消除） the
possible hazard （危险） that may be caused by changing
clearances or permanent（永久的） entrapment and pinching（收
宿）of fixed openings.(<5mm or >13mm)
11. Resistance To Hot Water
11 Effects Of Extreme Temperature
12. Resistance（抵抗力） To Corrosion
（侵蚀） (Metal Components)
13. Effects Of Humidity（湿度）
Pour 25 mL. of boiling water and allow cooling. Dry surface, Shall
be no graying（灰色） or spotting（斑点）
24 Hours At -32° F And 140°F - No failure
corrosion or visual change.
No change after 24 hours. @ 95% RH & 100°F


Shall withstand（抵挡） 24 hours in 1% salt spray (fog) with no
14. Stain（污点） Resistance- (Do not Various food materials – should resist permanent staining.( After 2
test on picnic table hours, remove)
racks) 1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original)
4. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft BBQ
Sauce (original) Red Wine
15 Resistance to Scratching Marring No scratching or marring of surface (3 cycles of 6” back and forth.)
Other Surfaces
16. Caster Performance (If Supplied)
17. Rear Stability背后的稳定性
Conduct with and without levelers. Note if levelers become bent
or come off. Note any damage defects (bentbroken levelers)
Max 5 lb pull to move under 200 lb load
Lbs. children) weight placed on the seat (Strap). Force is applied
in rearward direction against 1inch obstruction. Report result
when seat is in minimum, midpoint and maximum position
18. Front Stability
Ottomans)
19. Tip Resistance (Stools Only)
20. Stability (Stools Only)
21. Base Durability（耐用力）
The chair is obstructed（阻塞） by 1 inch bar in the front base,
force shall not be less than 40% of the total chair weight.
Min 10 degree with 150 Lbs. (Children 100 Lbs.) distributed load,
no tip- over
Min 20 Lbs. pull force after 150 Lbs. (Children 100 Lbs.) distributed
load on the seat, no tip-over
No structural（结构的） failure or permanent（永久的） deformation
（变形） under 400 Lbs. (225 Lbs. children) static （静力的） load
for 60 minutes. For multi seatback positions, report result when
seat back is in minimum, midpoint, and maximum positions for 20
minutes each.
22. Front Seating Capability
(Excludes Barstools & Ottomans)
23. Impact（碰撞） Durability
without cushion（垫子）)
No structural breakage, max ? inch deformation（变形） when 225
children) test load free falls from 6 inch to the center of the seat.
For multi seatback positions, report result when seat back is in
minimum, midpoint, and maximum positions. If chair has levelers,
conduct test with levelers fully extended then rotated（旋转） inward
（向内的） two revolutions.

(*If applicable – perform with and Lbs. (200 Lbs. folding chairs, 175 Lbs ottomans, 100 Lbs.
No failure under 300 Lbs. (135 Lbs. children) loading at edge (6 In.)

(Excludes（把 …除外） Barstools & tipping force is measured in the 45° to the test platform. The tipping

Min 35 Lbs. (30 Lbs. children) tipping force with a 173 Lbs. (100

24. Back Pull Durability后拉力 耐久力
25. Arm Strength Test (Vertical垂直的)

No failure at 100 Lbs. (60 Lbs. children) for 1 min. applied（应用） to
90° from back at 16 inch above the seat.
No permanent deformation at 300 Lbs. (90 Lbs. children) for 1 min.
The vertical（吹垂直的） load is uniformly（均一的） applied through
a 5 inch wide board across both arms – No failure deformation
26．Arm Strength Test (Horizontal水平
的)
No permanent deformation at 75 Lbs. (45 Lbs. children) for 1 min.
The load is applied to the armrest horizontally at the most forward
point of the armrest area.
No failure or permanent deformation at 75 Lbs. (40 Lbs. Child
folding chairs) applied to each leg at 1 inch from the end of the leg.
Force is applied in four directions (Forward, rearward, side and
side) for 1 minute.
27. Leg Strength腿力量

36. Moisture Content (%) (Solid Wood 8% - 12% (Do not test on MDF)
Only)湿度
37. Lightfastness （耐光性） Class 4.0 @ 20 hrs - Test up to 5 majormain components







MTL SGS TEST LIST (2)

(CD chest)
Quality test standardmethod
ng DesignFeatures
ctions
Criteria
The actuality must keep consistency with the claim.
use, maintenance, cleaning and safety information as required in
the language(s) applicable to the destination country(s) with no
errors or spelling mistakes. Shall be easy to follow and accurate.
t sizeweight
Statement
Report actual. Shall comply with any claims (-0%, +3%)
greater are used in inner packaging, the following warning
statement must be printed on at least one side of each bag in
English, French and Spanish:
5. Lead In Surface Coating
6. Workmanship Level
Shall not exceed（超越） 600 ppm (0.06% by weight) total lead
?
?
?
?
?
?
?

No major defects
No components missing, malformed（难看的） or fractured
（破裂）
No hardware missing
Smoothly ground welds（接合）, not over-ground and free
of pits and splatter
No burrs
No loose components and unsecured fastening where
rigidity （硬度）is required
In the case of wood (e.g. laminates薄片) proper and





Results

Shall be included if necessary. Shall include assembly, mounting,
4. Costco Plastic Bag Warning If plastic bags (of any thickness) with a perimeter of 14 inches or

uniform adhesion
?
?
?
?
?
7. Sharp Points and Edges
8. Cross Cut Adhesion（粘着力）

No scratches, dents, cracks, marred or discolored surface
In the case of molded plastic, consistent and concise form
and no defects evidencing迹象 of overuse of mold.
Finished edges and seams
Accurate and consistent painting
Components even in color, uniform clarity
Shall have no sharp edges or sharp points on any component other
than those required for functional use.
Plating （电镀） finish must stay affixed（粘贴） – using a utility
knife, cut a grid（格子） of 16 squares. Use 3M masking tape
(#202), apply to the grid. Remove to see if plating finish remains
intact.（完整无缺的）
9. Glass Top Thickness (Raw Edge If less than 7.6 mm, tempered glass required. If 7.6 mm or greater,
(mm)
(mm)
Test Filled and Unfilled.)
11 Effects Of Extreme Temperature
Components)
13. Effects Of Humidity
picnic table racks)
tempered glass not required.
tempered glass not required
and configuration, without tip over.
24 Hours At -32° F And 140°F - No failure
visual change.
No change after 24 hours. @ 95% RH & 100°F
hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original) “
5. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft BBQ
Sauce (original) Red Wine
15 Resistance to Scratching Marring No scratching or marring of surface (3 cycles of 6” back and forth.)
Other Surfaces
16. Handle Strength
17. Drop Test
Or Greater Than 20 Inches Width)
Conduct with and without levelers. Note if levelers become bent
or come off. Note any damage defects (bentbroken levelers)
Shall withstand 1.5 x claimed load or 50 lbs for 1 hour



10. Glass top Thickness (Encased) If less than 4.6 mm, tempered glass required. If 4.6 mm or greater,
11. Stability – Static (If Applicable – Shall withstand an 8° angle of incline, in the least stable positioning
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no corrosion or
14. Stain Resistance- (Do not test on Various food materials – should resist permanent staining.( After 2
Raise the end of the long axis of the storage unit to the specified
shall be no damage as a result of the test.
Drop Height 10 inches (Unit Weight 10-49 Lbs) 6 Inches (Unit
Weight 50-99 Lbs
4 Inches (Unit Weight 100-200 Lbs)
2 Inches (Unit Weight >200 Lbs):
(For Units 30 Inches Height Or Over, height and release the end. Repeat test for the other end. There
18. Drop Test (For Units Under 30 No breakage or separation after 3 drops from 12 inches on vinyl tile
Inches Height And Less Than 20 over concrete.
Inches Width Or With Total Weight CDAudio tapeor Video tape Holder –
Under 10 Lbs)
Only)

No failure or deformation after 1 drop on end from 10 inches
19. Moisture Content (%)(Solid Wood 8% - 12% (Do not test on MDF)

20. Cycle Test Test for Moving 100 times cycles use of moving components – no failure and all
Components
21. Finger Entrapment
components must have and maintain a smooth uniform movement
throughout each cycle
Shall meet the requirements intended to eliminate the possible
hazard that may be caused by changing clearances or permanent
entrapment and pinching of fixed openings.(<5mm or >13mm)
22. Resistance To Hot Water Pour 25 ml of boiling water and allow cooling. Dry surface, Shall be
no graying or spotting
23. Cap Removal Strength on end of Shall not separate minimum holding force @ 5.0 lbs.
tubes (or cap covers on screw ends)
24. Caster Performance (If Supplied)
25. CasterRoller Durability
Max 20 lbs. pull to move under 200 lbs. load.
Shall result in no adverse effects on rolling after use tests.
Rolling 100 meters on smooth concrete floor under uniformly
distributed load:
200 lbs for Serving CartRack 500 lbs for larger CabinetsShelves
26 Drawer Loading Capacity
Magazine, Shoe, Coat or Wine Racks)

Max. 14 in. deformation @ 10 lbs distributed load drawer
greater than ? inch.
< 8 In. Depth (3 Lbs. X ShelfTop Width) 8 - 16 In. Depth (5 Lbs. X
ShelfTop Width)
>16 In. Depth (7 Lbs. X ShelfTop Width)
Or 1.5 x Claimed Capacity
28. Concentrated Load No structural failure or more than ? inches deformation when load
(For Floor Standing Units Up To 38 is applied to a 12 inches diameter disk located such that the center
Inches Height, Except Magazine, of the disk is 6 inches from the edge of the top surface
Shoe, Coat or Wine Racks)
29. Stability
(For Units Over 42 inches Height)
30. Stability
Inches Height)
31. Racking Test
32. Leg Strength (SideFront)

Top Surface Area > 4 sq ft – 300 lbs< 4 sq ft – 200 lbs
No tip-over should occur under the following conditions
No tip over should occur under the following conditions
1 inches from the edge of 12 inches disk
> 4 sq ft – 100 lbs<4 sq ft - 90 lbs
No structural damage or deformation when the unit is raised 45
degrees from the floor
75 lbs (40 lbs if Unit is less than 30 inches height) applied vertically
to the leg at 1inch from the end of the leg. Force is applied in 4
directions (Forwardrearward, side to side). No failurepermanent
deformation
33. Impact Durability
enance Loading
No structural breakage when 200 lbs test load falls 6 inches to the
center of the top.
Test For units over 30 Inch height, apply a 50 lb downward force for 1
minute to any portion of the unit within 30 inches of the floor that is
likely to support part or all of a child’s weight. There shall be no
tip-over of the unit
35. Drawer Operability Max 10 lbs pull force with distributed drawer load (30 lbscubic ft –
10 lbs minimum)

(Tip-Over Resistance)


Horizontal force of 40 lbs or an angle > 10 deg before tipping occur




27. Distributed Load Test(Except There shall be no structural failure or permanent deformation
(For Floor Standing Units Up to 42 Must not have any one leg lift off the floor when test load is applied

36. Extendible ShelvesSupports

Max 10 lbs pull force with distributed load (per table 1a, see last
page of protocol)
37. Lightfastness (Indoor Use –For Class 4.0 @ 20 hrs - Test up to 5 majormain components
Hard Materials Only)





MTL SGS TEST LIST (3)
(Home Entertainment Center TV Stand (UL 1678 4
th
Ed.)
Quality test standardmethod

Criteria

ng DesignFeatures
The actuality must keep consistency with the claim.

ctions
Results

Shall be included if necessary. Shall include assembly,
mounting, use, maintenance, cleaning and safety information
as required in the language(s) applicable to the destination
country(s) with no errors or spelling mistakes. Shall be easy
to follow and accurate.
Report actual. Shall comply with any claims (-0%, +3%)
3.
product sizeweight
4. Costco Plastic Bag Warning
If plastic bags (of any thickness) with a perimeter of 14 inches or greater

are used in inner packaging, the following warning statement must be
Statement

printed on at least one side of each bag in English, French and Spanish:

5. Lead In Surface Coating

6. Workmanship Level
Shall not exceed 600 ppm (0.06% by weight) total lead
?
?
?
?
No major defects
No components missing, malformed or fractured
No hardware missing
Smoothly ground welds, not over-ground and free of
pits and splatter


? No burrs
? No loose components and unsecured fastening where
rigidity is required
? In the case of wood (e.g. laminates) proper and
uniform adhesion
? No scratches, dents, cracks, marred or discolored
surface
? In the case of molded plastic, consistent and concise
form and no defects evidencing of overuse of mold.
? Finished edges and seams
? Accurate and consistent painting
? Components even in color, uniform clarity
Shall have no sharp edges or sharp points on any component
other than those required for functional use.
Plating finish must stay affixed – using a utility knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to
the grid. Remove to see if plating finish remains intact.

7. Sharp Points and Edges
8. Cross Cut Adhesion

9. Glass Top Thickness (Raw Edge If less than 7.6 mm, tempered glass required. If 7.6 mm or
(mm) greater, tempered glass not required.
10. Glass top Thickness (Encased) If less than 4.6 mm, tempered glass required. If 4.6 mm or
(mm) greater, tempered glass not required
11. Stability – Static (If Applicable – Shall withstand an 8° angle of incline, in the least stable
Test Filled and Unfilled.) positioning and configuration, without tip over.
11 Effects Of Extreme Temperature 24 Hours At -32° F And 140°F - No failure
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no
Components) corrosion or visual change.
13. Effects Of Humidity No change after 24 hours. @ 95% RH & 100°F
14. Stain Resistance- (Do not test on Various food materials – should resist permanent
picnic table racks) staining.( After 2 hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original) “
6. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft
BBQ Sauce (original) Red Wine
15 Resistance to Scratching Marring
No scratching or marring of surface (3 cycles of 6” back and

Other Surfaces forth.)Conduct with and without levelers .Note if levelers
become bent or come off. Note any damage defects
(bentbroken levelers)
16. Caster Performance (If Supplied)
17. Temperature Stability Test
Max 5 Lbs. pull to move under 200 Lbs. load
A cart or stand employing polymeric materials in its
construction shall withstand 7 hours of exposure in a
full-draft circulating air oven maintained at 70 ?C without any
shrinkage, warpage or other distortion.
18. Tip Stability Test –Conventional A cart or stand not intended for use with a television, shall not
Television tip over when placed at the center of a plane inclined to make
an angle of 10 degrees with the horizontal and loaded as
specified in table 13.1 of this standard. A cart or stand
intended for use with a television shall not tip over when
placed at the center of a plane to 10 degrees with the
horizontal with the surface intended to support a television
loaded with the simulated television load described in section
13.4. If the manufacturer specifies a television range, then the
test is to be conducted with the simulated loads within the
range specified. The test is to be conducted according to all of
the stipulations of this section of the standard.
19. Moisture Content (%)(Solid 8% - 12% (Do not test on MDF)
Wood Only)

20. Tip Stability Test – Flat Panel TV As described in section, shall not tip over when placed at the
Rack center of a plane to 10° with the horizontal with a simulated
load per table 13.2 attached to the flat panel TV rack.
21. Loading Test – Individual A cart or stand shall be constructed so that there is no collapse
Loading (Conventional TV Stand ) or permanent damage that results in risk of injury to persons
when each supporting surface it individually loaded with:
a) Two times the load specified in table 13.1 plus 100

pounds for the surface intended to support a
television;
b) Four times the load specified in table 13.1, not to
exceed 100 pounds for all other supporting surfaces;
or
c) The maximum intended load for a dedicated storage
area intended to accommodate a specific accessory.
Each supporting surface shall be tested for one minute with
the other supporting surfaces unloaded.
22. Finger Entrapment Shall meet the requirements intended to eliminate the possible
hazard that may be caused by changing clearances or
permanent entrapment and pinching of fixed openings.(<5mm
or >13mm)
23. Loading Test - Individual A cart or stand shall be constructed so that there is no collapse
Loading or permanent damage that results in risk of injury to persons
(Flat Panel TV Stand ) when each supporting surface it individually loaded with:
a) 200 pounds for flat panel TV rack;
b) Four times the load specified in Table 13.1, not to exceed
100 pounds for all other supporting surfaces; or
c) The maximum intended load for a dedicated storage area
intended to accommodate a specific accessory.
Each supporting surface shall be tested for one minute with
the other supporting surfaces unloaded.
24. Loading Test – Simultaneous The cart or stand shall be constructed so that there is no
Loading collapse or permanent damage that results in a risk of injury
(Conventional TV Stand ) to persons when each supporting surface is simultaneously
loaded with the load specified in table 13.1 for a period of one
minute. Modification = test to 300 pounds.
25. Loading Test - Simultaneous The cart or stand shall be constructed so that there is no
Loading collapse or permanent damage that results in a risk of injury
(Flat Panel TV Stand ) to persons when each supporting surface is simultaneously
loaded with the load specified in Table 13.1 for a period of
one minute. Modification = Test flat panel TV rack to 200 Lbs
or manufacturer’s specified load, whichever is greater.
26 Wall or Ceiling Mounting A shelf or similar product intended for direct wall mounting
Security Test shall be so constructed so that there is no cracking or breaking
or damage to the mounting bracket, its securing means and
the portion of the shelf attached to it when each supporting
surface is both individually and simultaneously loaded with
four times the load specified in table 13.1 for one minute
27. Appurtenance Loading Test
(Tip-Over Resistance)
For units over 30 Inch height, apply a 50 Lb downward force
for 1 minute to any portion of the unit within 30 inches of the
floor that is likely to support part or all of a child’s weight.
There shall be no tip-over of the unit
Structural glass parts shall comply with the requirements in
the impact test, section 19. A decorative glass part having an

28. Impact Test – Glass Parts

area greater than 1 Ft
2
or having a minor dimension greater
than 18 inches, shall not be broken, shattered (totally or in
part), or displaced when tested as described in 20.3 of this
section.
29．Impact Durability (B) - for units
No structural breakage when 200 Lbs. test load falls free from
under 30 inches high 6 In. to the center of the top with no static load in the other
half of the top
30. Front Seating Capability (For No failure under 300 Lbs loading at 6 inches at edge (6
Floor Standing Units Under 30 Inch inches)
Height And Flat Horizontal Top
Surface Which May Be Sat On)
31. Drawer Operability
32. Racking Test
33. Leg Strength
After distributed loading of 10 Lbs. drawer, max. 10 Lbs.
pull force
No structural damage or deformation when the unit is raised
45° from the floor
No structural failure at 75 Lbs. (40 Lbs. if folding legs or if
children’s furniture) applied vertically to each leg type at 1
inch from the end of the leg. Force is applied in four
directions (forward rearward, side to side)
Each enclosed area of a cart or stand intended to
accommodate electrical equipment shall be provided with a
means for ventilation when the equipment is installed.
Max 10 lbs pull force with distributed drawer load (30
lbscubic ft – 10 lbs minimum)
Max 10 lbs pull force with distributed load (per table 1a, see
last page of protocol)

34. Ventilation
35. Drawer Operability
36. Extendible ShelvesSupports
37. Lightfastness (Indoor Use –For Class 4.0 @ 20 hrs - Test up to 5 majormain components
Hard Materials Only)
Table 13.1
Supporting surface loading parameters

Surface Type
TV shelf


Other supporting surface

Dedicated storage area
Load

Weight specified in Table 13.2 or
manufacturer’s specified load, whichever
is greater.

Manufacturer specified load or 25 lbs.,
whichever is greater

Fully loaded with intended load


able 13.2 Simulated Television Load ParametersT

Maximum screen diagonal measurement
ecommended for use with surface, inches
(cm)
CRT TELEVISIONS
Up to 13 (33.02)
14 – 16 (35.56 – 40.64)
17 – 20 (43.18 – 50.80)
21 – 24 (53.34 – 60.96)
25 – 27 (63.50 – 68.58)
28 – 32 (71.12 – 81.28)
33 – 35 (83.82 – 88.90)
36 – 40 (91.44 – 101.60)


Total weight
b
, lbs (kg)
25 (11.34)
35 (15.88)
50 (22.68)
70 (31.75)
95 (43.09)
135 (61.23)
175 (79.38)
240 (108.86)


Total weight
b
, lbs (kg)
80 (36.3)
100 (45.4)
135 (61.4)
135 (61.4)
135 (61.4)
Height above supporting
surface to center of support
rod, inches (cm)
6-34 (17.15)
7-12 (19.05)
9 (22.86)
10 (25.40)
11 (27.94)
13 (33.02)
15 (38.10)
17 (43.18)
Height above supporting
surface to center of support
rod, inches (cm)
16 (40.6)
18 (45.7)
20 (50.8)
21(53.3)
22 (55.8)

Angle of unstable equilibrium
25°
25°
22°
21°
20°
(12 °)
(12 °)
(12 °)
Maximum screen diagonal measurement
ecommended for use with surface, inches
(cm)
PLASMA LCD TELEVISIONS
30 – 40 (76.2 – 101.6)
41 – 45 (104.1 – 114.3)
46 - 50 (116.8 – 127.0)
51 – 55 (129.4 – 139.7)
56 – 60 (142.2 – 152.4)

Angle of unstable equilibrium
12 °
12 °
12 °
12 °
12 °
The fixture shall be stable in the forward direction at the angle specified and become unstable (tip over) when the angle is increased b
degree.
Includes weight of text fixture.
MTL SGS TEST LIST (4)
Bed (For Trundle and Regular Beds, Adult use)
Quality test standardmethod

ng DesignFeatures
ctions
Criteria

The actuality must keep consistency with the claim.

Results

Shall be included if necessary. Shall include assembly,
mounting, use, maintenance, cleaning and safety information
as required in the language(s) applicable to the destination
country(s) with no errors or spelling mistakes. Shall be easy
to follow and accurate.


Report actual. Shall comply with any claims (-0%, +3%)
3.
product sizeweight
4. Costco Plastic Bag Warning
If plastic bags (of any thickness) with a perimeter of 14 inches or
greater are used in inner packaging, the following warning statement
Statement

must be printed on at least one side of each bag in English, French and
Spanish:

5. Lead In Surface Coating

6. Workmanship Level
Shall not exceed 600 ppm (0.06% by weight) total lead
? No major defects
? No components missing, malformed or fractured
? No hardware missing

? Smoothly ground welds, not over-ground and free of
pits and splatter
? No burrs
? No loose components and unsecured fastening where
rigidity is required
? In the case of wood (e.g. laminates) proper and
uniform adhesion
? No scratches, dents, cracks, marred or discolored
surface
? In the case of molded plastic, consistent and concise
form and no defects evidencing of overuse of mold.
? Finished edges and seams
? Accurate and consistent painting
? Components even in color, uniform clarity
? All seams and components in even alignment
Shall have no sharp edges or sharp points on any component
other than those required for functional use.
Plating finish must stay affixed – using a utility knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to
the grid. Remove to see if plating finish remains intact.
Applicable by design – must sit level with no wobbling on a
flat level surface. The top must also be levelparallel
compared to the bottom.
7. Sharp Points and Edges
8. Cross Cut Adhesion
9. Level
10. Cycle Test Test For Moving 100 times cycles use of moving components – no failure and
Components all components must have and maintain a smooth uniform
movement throughout each cycle. (All functional parts must
be evenly aligned at the start of the test and remain evenly
aligned.)
11. Folding Mechanisms and Hinges Shall meet the requirements to eliminate the possible
crushing, laceration or pinching hazards that might occur in
folding mechanisms and hinges.
24 Hours At -32° F And 140°F - No failure 11 Effects Of Extreme Temperature
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no
Components) corrosion or visual change.
13. Effects Of Humidity No change after 24 hours. @ 95% RH & 100°F
14. Stain Resistance- (Do not test on Various food materials – should resist permanent
picnic table racks) staining.( After 2 hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original) “
7. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft
BBQ Sauce (original) Red Wine
15 Resistance to Scratching Marring
No scratching or marring of surface (3 cycles of 6” back and

Other Surfaces forth.)Conduct with and without levelers .Note if levelers
become bent or come off. Note any damage defects
(bentbroken levelers)
16. Caster Performance (If Supplied)

Shall not separate minimum holding force @ 5.0 lbs

17. Cap Removal Strength (on end of Shall not separate minimum holding force @ 5.0 lbs
tubes) (or Cap Covers on screw
ends)
18. Drop Impact Test

One end of the bed is dropped from a height of 10 inches.
No failurepermanent deformation
19. Moisture Content (%)(Solid 8% - 12% (Do not test on MDF)
Wood Only)
20. Distributed Static Load No structural failure or greater than 14 inch permanent
deformation after loading for 60 minutes
Single - 500 lbs
FullQueenKing – 800 lbs
21. Lightfastness (Indoor Use –For Class 4.0 @ 20 hrs - Test up to 5 majormain components
Hard Materials Only)









MTL SGS TEST LIST (5)
（Bunk Bed）
Quality test standardmethod

ng DesignFeatures
ctions
Criteria

The actuality must keep consistency with the claim.

Results

Shall be included if necessary. Shall include assembly,
mounting, use, maintenance, cleaning and safety information
as required in the language(s) applicable to the destination
country(s) with no errors or spelling mistakes. Shall be easy
to follow and accurate.


Report actual. Shall comply with any claims (-0%, +3%)
3.
product sizeweight
4. Costco Plastic Bag Warning
If plastic bags (of any thickness) with a perimeter of 14 inches or
greater are used in inner packaging, the following warning statement
Statement

must be printed on at least one side of each bag in English, French and
Spanish:

5. Lead In Surface Coating

6. Workmanship Level
Shall not exceed 600 ppm (0.06% by weight) total lead
?
?
?
?
No major defects
No components missing, malformed or fractured
No hardware missing
Smoothly ground welds, not over-ground and free of
pits and splatter


? No burrs
? No loose components and unsecured fastening where

rigidity is required
? In the case of wood (e.g. laminates) proper and
uniform adhesion
? No scratches, dents, cracks, marred or discolored
surface
? In the case of molded plastic, consistent and concise
form and no defects evidencing of overuse of mold.
? Finished edges and seams
? Accurate and consistent painting
? Components even in color, uniform clarity
Shall have no sharp edges or sharp points on any component
other than those required for functional use.
Plating finish must stay affixed – using a utility knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to
the grid. Remove to see if plating finish remains intact.
Products intended for children under 36 months (3 years) of
age shall not include removable, liberated components, or
fragments of products after use and abuse that are small
enough (without being compressed) to fit entirely within the
small parts cylinder
7. Sharp Points and Edges
8. Cross Cut Adhesion
9. Small Objects
10. Accessible Edges Accessible Products intended for children under 8 years of age shall not
Points have accessible, potentially hazardous sharp edges before or
after use and abuse testing
11. Level Applicable by design – must sit level with no wobbling on a
flat level surface. The top must also be levelparallel
compared to the bottom.
24 Hours At -32° F And 140°F - No failure 11 Effects Of Extreme Temperature
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no
Components) corrosion or visual change.
13. Effects Of Humidity No change after 24 hours. @ 95% RH & 100°F
14. Stain Resistance- (Do not test on Various food materials – should resist permanent
picnic table racks) staining.( After 2 hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original) “
8. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft
BBQ Sauce (original) Red Wine
15 Resistance to Scratching Marring
No scratching or marring of surface (3 cycles of 6” back and

Other Surfaces forth.)Conduct with and without levelers .Note if levelers
become bent or come off. Note any damage defects
(bentbroken levelers)
16. Cycle Test Test for Moving 100 times cycles use of moving components – no failure and
Components all components must have and maintain a smooth uniform
movement throughout each cycle. (All functional parts must
be evenly aligned at the start of the test and remain evenly
aligned.)
17. Folding Mechanisms and Hinges

Shall meet the requirements to eliminate the possible

crushing, laceration or pinching hazards that might occur in
folding mechanisms and hinges.
18. Resistance To Hot Water Pour 25ml of boiling water and allow cooling. Dry surface,
Shall be no graying or spotting


19. Moisture Content (%)(Solid 8% - 12% (Do not test on MDF)
Wood Only)
20. Cap Removal Strength (On end of Shall not separate minimum holding force @ 5.0 lbs.
tubes) OR (Cap Covers on Screw
Ends)
21. Mechanical Hazards
A furniture article intended for use by a child shall not present a
mechanical hazard in normal use or when subjected to reasonable
foreseeable abuse:

? From fracture, fragmentation, or disassembly of the
article
? From propulsion of the article or any part or accessory
thereof
? From points or other protrusions, surfaces, edges,
openings or closures
? From moving parts
? From lack or insufficiency of controls to reduce or stop
motion
? As a result of self-adhering characteristics of the article
? Because the article or any part or accessory thereof may
be aspirated or ingested
? Because of instability
Because of any other aspect of the articles’ design or
manufacture.
22. Fit of Top Bed to Bottom Bed The bed post shall be designed so that the minimum height of
lift to allow horizontal disengagement of the top bed from the
bottom bed shall be 1 ?
may be used to prevent disengagement of the top bed from
the bottom bed.
23. Mattress and Foundation Size and Shall be no gaps between interior bed structure and the edges
Fit of the mattress and foundation that will permit complete
passage of wedge block when tested in accordance with 5.2.
24. Foundation Support System Shall confine the horizontal position of the mattress and the
foundation and shall prohibit the mattress and foundation
from falling into the clearance over the lower bunk or to the
floor when it is manipulated.
A minimum of two per bed are required if cross- members
are utilized.
They shall be spaced if more than two are utilized so that the
distance between adjacent cross-members or between the
cross-members and the bed end structures will not permit
complete passage of the wedge block or will allow complete
passage of both the wedge block and the 9 in.(230 mm)

diameter rigid sphere when tested in accordance with 5.8.
25. Bolt-On Side Rails
? Shall be secured at each end by two bolts with a
(Attach at their ends or on their side minimum size of 14 in. (6 mm) diameter.
to the Bed post)
? Bolts shall be spaced a minimum of 1? in. (40 mm) apart
on their centers for wood beds.
No more than ? in (6 mm) of thread shall be exposed when
the bolts are fully tightened in the assembled bed.
Hook-on attachments shall require an additional action other
26 。Hook-On Side Rails
(Securely attached to the Bed than an upward force to disengage.
post)
27. Side Rails Attachments
28. Guardrails
Shall be no structural failure of bedside rail fastening systems
when tested in accordance with 5.4.
Two guardrails shall accompany any bed in which the
underside of foundation is over 30in (762 mm) from the floor.
Guardrails may be separate from or integral with the ladder.
Shall be attached so that requires the intentional release of
fastening device or cannot be removed unless forces are
applied sequentially in different directions
The upper edge of guardrails shall be at least 5in. (130 mm)
above the sleeping surface when a mattress of a thickness that
is the maximum specified by the manufacturer’s instructions
is used on the bed.
With no mattress on the bed, there shall be no openings in the
rigid bed structure below the lower edge of any opening of
the guardrail that would permit complete passage of wedge
block when tested in accordance with 5.5.
A guardrail may terminate before reaching the bed end structure,
providing there is no more than 15 in. (380 mm) between either end of
the guardrail and the bed end structures in the same plane when
measured at a point 5 in. (127 mm) above the sleeping surface as
established by the maximum mattress thickness specified by the
manufacturer. The second guardrail may terminate before reaching the
bed end structure. There shall be no more than 0.22 in. (5.6 mm)
between either end of the guardrail and the bed end structure when
measured horizontally between the bed end structure and the nearest
point on the guardrail if this guardrail terminates before reaching the
bed end structure.
For bunk beds designed to have a ladder attached to one side
of the bed, the continuous guardrail shall be on the other side
of the bed.
29．I Upper Edge of Upper Bunk End
Structure
(Refer Criteria for Full
Description)

The upper edge of upper bunk end structures for at least 50%
of distance between the two posts at the head and foot of the
upper bunk shall be at least 5 in. (130 mm) above the sleeping
surface when a mattress and foundation of the maximum size
and thickness specified by the manufacturer’s instructional
literature is used on the upper bunk.

30. Rigid End Structure of the Upper There shall be no openings in the rigid end structures of the
Bunk upper bunk that will permit the free passage of the wedge
(Refer Criteria for Full Description) block when tested in accordance with 5.6.1. It shall apply
only to that portion of the bed end structure that is above the
foundation support system of the upper bunk.
31. End Structure of the Lower Bunk,
Between Lower Bunk Foundation and
the Lower Level of Upper Foundation
(Refer to Criteria for Full
Description)
There shall be no openings in the end structures of the lower
bunk that will permit free passage of the wedge block when
tested in accordance with 5.6.2, unless they are large enough
to permit the free passage of a 9 in.(230 mm) diameter rigid
sphere. It does not apply to openings that are below the level
of the lower bunk foundation support system. It shall apply to
that portion of the bed end structure that is between the level
of the lower bunk foundation support system and the level of
the upper bunk foundation support system..
32. Lower Bunk End Structure All portions of the boundary of any opening of the lower
(Refer to Criteria for Full bunk end structure that permits free passage of a 9in (230
Description) mm) diameter rigid sphere also must conform to the neck
entrapment requirement when tested in accordance with
5.6.2.3 and 5.6.2.4.
33. Ladders Lean-on or hang-on ladder must be supplied with each bunk
bed set or incorporated as part of the bed structure. May be
separated from or integral with the guardrail. Shall be
attached in a manner that prevents inadvertent
disengagement, repositioning or tilting when in use.
The width of the ladder shall be no less than 10 in. (250 mm)
measured from the inside of the stiles. Vertical spacing of
ladder steps shall be no greater than 12 in (300 mm) when
measured from the floor to first step or between steps.
Vertical spacing may be up to 16in.(400 mm) when bed
structures are used as ladders.
Shall be no separation of any of the attachments of the
foundation support system to the end structures of the bed
when tested in accordance with 5.7.1.1 and 5.7.2.
Shall be tested to substantiate care label content. Children’s
furniture which is not required to contain a care label but has
a label present shall be laundered according to label
instructions only. A general appearance evaluation shall be
conducted.

34. *Frame and Fastenings
(Racking test - Metal beds only)
35. Care Label
36. Lightfastness (Indoor Use –For Class 4.0 @ 20 hrs - Test up to 5 majormain components
Hard Materials Only)

MTL SGS TEST LIST (6)
（Tables (Combines Adult and Children’s sizes, IndoorOutdoor, for the following styles:
Dining, camping, occasional and coffee tables, desks, nightstands, work bench, potting bench, storage
bench)
Quality test standardmethod

ng DesignFeatures（标签
ctions（用发说明书）
Criteria

The actuality must keep consistency with the claim.

Results

Shall be included if necessary. Shall include assembly,
mounting, use, maintenance, cleaning and safety information
as required in the language(s) applicable to the destination
country(s) with no errors or spelling mistakes. Shall be easy
to follow and accurate.
Report actual. Shall comply with any claims (-0%, +3%)

3.
product sizeweight产品尺寸
重量
4. Costco Plastic Bag Warning
If plastic bags (of any thickness) with a perimeter of 14 inches or
greater are used in inner packaging, the following warning statement
Statement

must be printed on at least one side of each bag in English, French and
Spanish:

5. Lead In Surface Coating

6. Workmanship Level
Shall not exceed 600 ppm (0.06% by weight) total lead
?
?
?
?
No major defects
No components missing, malformed or fractured
No hardware missing
Smoothly ground welds, not over-ground and free of
pits and splatter


? No burrs
? No loose components and unsecured fastening where
rigidity is required
? In the case of wood (e.g. laminates) proper and
uniform adhesion
? No scratches, dents, cracks, marred or discolored
surface
? In the case of molded plastic, consistent and concise
form and no defects evidencing of overuse of mold.
? Finished edges and seams

7. Sharp Points and Edges
8. Cross Cut Adhesion
? Accurate and consistent painting
? Components even in color, uniform clarity
Shall have no sharp edges or sharp points on any component
other than those required for functional use.
Plating finish must stay affixed – using a utility knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to
the grid. Remove to see if plating finish remains intact.
9. Glass Top Thickness (Raw Edge If less than 7.6 mm, tempered glass required. If 7.6 mm or
(mm) greater, tempered glass not required.
10. Glass top Thickness (Encased) If less than 4.6 mm, tempered glass required. If 4.6 mm or
(mm) greater, tempered glass not required
11. Stability – Static (If Applicable – Shall withstand an 8° angle of incline, in the least stable
Test Filled and Unfilled.) positioning and configuration, without tip over.
11 Effects Of Extreme Temperature 24 Hours At -32° F And 140°F - No failure
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no
Components) corrosion or visual change.
13. Effects Of Humidity No change after 24 hours. @ 95% RH & 100°F
14. Stain Resistance- (Do not test on Various food materials – should resist permanent
picnic table racks) staining.( After 2 hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original) “
9. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft
BBQ Sauce (original) Red Wine
15 Resistance to Scratching Marring
No scratching or marring of surface (3 cycles of 6” back and

Other Surfaces forth.)Conduct with and without levelers .Note if levelers
become bent or come off. Note any damage defects
(bentbroken levelers)
16. Caster Performance (If Supplied)
17. Cycle Test Test for Moving
Components (Drawers, Doors,
Keyboard Trays, Drop Leaf, Locking
Device, etc)
18. Folding Mechanisms and Hinges
Max 5 Lbs. pull to move under 200 Lbs. load
100 times cycles use of moving components – no failure and
all components must have and maintain a smooth uniform
movement throughout each cycle. (All functional parts must
be evenly aligned at the start of the test and remain evenly
aligned.)
Shall meet the requirements to eliminate the possible
crushing, laceration or pinching hazards that might occur in
folding mechanisms and hinges.
19. Moisture Content (%)(Solid 8% - 12% (Do not test on MDF)
Wood Only)
20. Resistance To Hot Water Pour 25 ml of boiling water and allow cooling. Dry surface.
Shall be no graying or spotting.
21. Cap Removal Strength (On end of Shall not separate minimum holding force @ 5.0 lbs.
tubes) OR (Cap Covers on Screw
Ends)
22. Caster Performance (If Supplied)
23. Shelf Loading Capacity
Max 5 lbs pull to move under 200 lbs load.
Max 14 inch deformation. Test load dependant on shelf
width and depth: Report deformation, shelf width and load

applied to shelf
<8 inch depth, (3 lbs x shelf width-inch)
8-16 inch depth, (5 lbs x shelf width-inch)
>16 inch depth (7 lbs x shelf width-inch)
24. Drawer Loading Capacity
25. Drawer Operability
Max 14 inch deformation @ 10 lbs distribute loaddrawer
Max 10 lbs pull force with 10 lbs distributed drawer load


26 Distributed Load Test On Max 14 inch deformation when 30 lbs distributed test load is
Keyboard Tray applied on surface for 60 minutes. No malfunction in
operability shall be noted after the test.
27. Keyboard Tray Operability
PERFORMANCE – TABLES, DESKS,
BENCHES (TYPE I)
After distributed load of 10 lbs is applied to the tray, it should
open with a maximum 5 lbs pull force
Use this section for Dinette, Casual, Card Tables, Desks,

Work Benches, with all components such as leaves, levelers.
*If levelers are provided, test with and without levelers at
additional cost.
*If leaves are provided, test additionally in largest
configuration at additional cost.
* If both are provided, test with and without leaf & levelers
in place

29．Distributed Load Capacity
Max 14 inch deformation and no malfunction in any
component when a uniformly distributed test load is applied
on the surface for 30 minutes.
Glass top: 100 lbs
Non-glass tops for outdoor use with height 24 inches or less:
400 lbs
The load applied shall be based on surface area if top is not
glass
Adultchildren
>4 sq ft: adult- 40 lbssq ft, children’s - 30 lbssq ft
< 4 sq ft: adult - 60 lbssq ft, children’s - 50 lbssq ft
Note: max load: 400 lbs (adult), 200 lbs (children)
No structural failure and max 12 inch deformation when test
load is placed on 12 inch diameter disc located such that the
center of the disc is 6 inch from the edge of the top surface
for 5 minutes.
Glass top: 100 lbs
The load applied shall be based on surface area if top is not
glass
Adultchildren
>4 sq ft: adult - 300 lbs, children’s - 200 lbs
< 4 sq ft: adult - 275 lbs, children’s - 175 lbs
Must not have any one leg lift off the floor when test load is
applied to a 12 inch disc located so that the edge of the disc is
1 inch from the edge of the top surface
Glass top: 100 lbs
The load applied shall be based on surface area if top is not

30. Concentrated Load Test
31. Stability

glass
Adultchildren
>4 sq ft: adult - 100 lbs, children’s - 75 lbs
< 4 sq ft: adult - 90 lbs, children’s - 65 lbs
32. Leg Strength No structural failure at 75 lbs (40 lbs if folding legs or if
children’s furniture) applied to each leg type at 1 inch from
the end of the leg. Force is applied in four directions
(forward, rearward, side to side)
No structural damage or deformation when the unit is raised
45 degrees from the floor
No structural breakage, 160 lbs test load free falls from 6 inch
to land in center of table (1 drop.) If chair has levelers,
conduct test with levelers fully extended then rotated inward
two revolutions.
Must be serviceable without any damage or malfunction
when one end of the unit is lifted and then dropped from a
height of 10 inch
Shall remain stable when tipped 8 degrees.



33. RockingRacking Test
(Folding Table Only)
34. Impact Durability (Only Perform
On Non-Glass Outdoor Tables. Not
Intended For Children’s Tables Which
Have A Height Of 24 Inches or Less)
35. Drop Impact Test
36. Stability Tip Test
(Bistro Table Only)
PERFORMANCE –COFFEE TABLES
(TYPE II)
Use this section for Coffee tables only

37．Distributed Load Capacity
Max ? inch deformation and no malfunction in any
component when a uniformly distributed test load is applied
on the surface for 30 minutes.
Glass top: 50 lbs
Non-glass tops for outdoor use with height 24 inches or less:
400 lbs
The load applied shall be based on surface area if top is not
glass
> 4 sq ft - 30 lbs sq ft
< 4 sq ft - 60 lbs sq ft
note: max load 400 lbs
No structural failure and max 12 inch deformation when test
load is placed on 12 inch diameter disc located such that the
center of the disc is 6 inch from the edge of the top surface
for 5 minutes.
Glass top: 50 lbs
The load applied shall be based on surface area if top is not
glass
>4 sq ft - 200 lbs
< 4 sq ft - 175 lbs
Must not have any one leg lift off the floor when test load is
applied 1 inch from the edge on 12 inch disc
Glass top: 50 lbs
The load applied shall be based on surface area if top is not

38．Concentrated Load Test
39．Stability

glass
>4 sq ft - 75 lbs
<4 sq ft - 65 lbs
40．Drop Impact Test
Must be serviceable without any damage or malfunction
when one end of the unit is lifted and then dropped from a
height of 10 inch
No structural failure at 75 lbs (40 lbs if folding legs or if
children’s furniture) applied vertically to each leg type at 1
inch from the end of the leg. Force is applied in four
directions (forward rearward, side to side)

41．Leg Strength
PERFORMANCE- END TABLES
Use this section for End tables, night stands

OR NIGHTSTANDS (TYPE III)
42．Distributed Load Capacity
Max 14 inch deformation and no malfunction in any
component when a uniformly distributed test load is applied
on the surface for 30 minutes.
Glass topnight stand: 50 lbs
Non-glass tops for outdoor use with height 24 inches or less:
400 lbs
The load applied shall be based on surface area if top is not
glass
> 4 sq ft - 10 lbs sq ft
< 4 sq ft - 20 lbs sq ft
Note: max load 400 lbs
No structural failure and max 12 inch deformation when test
load is placed on 12 inch diameter disc diameter disc located
such that the center of the disc is 6 inch from the edge of the
top surface for 5 minutes.
Glass topnight stand: 50 lbs
The load applied shall be based on surface area if top is not
glass
>4 sq ft - 50 lbs
< 4 sq ft - 25 lbs
Must not have any one leg lift off the floor when test load is
applied 1 inch. From the edge on 12 inch. Disc
Glass top: 100 lbs
The load applied shall be based on surface area if top is not
glass
>4 sq ft - 50 lbs
< 4 sq ft - 40 lbs
No structural failure at 75 lbs (40 lbs if folding legs or if
children’s furniture) applied vertically to each leg type at 1
inch from the end of the leg. Force is applied in four
directions (forward rearward, side to side)
Must be serviceable without any damage or malfunction
when one end of the unit is lifted and then dropped from a
height of 10 inch

43．Concentrated Load Test
44．Stability
45．Leg Strength (Table)
46．Drop Impact Test

47. Lightfastness (Indoor Use –For Class 4.0 @ 20 hrs - Test up to 5 majormain components
Hard Materials Only)

MTL SGS TEST LIST (7)
(Seating)

(Combines Adult and Children’s sizes,:Chairs, Barstools, Ottomans,)
Quality test standardmethod

ng DesignFeatures
ctions
Criteria

The actuality must keep consistency with the claim.

Results

Shall be included if necessary. Shall include assembly,
mounting, use, maintenance, cleaning and safety information
as required in the language(s) applicable to the destination
country(s) with no errors or spelling mistakes. Shall be easy
to follow and accurate.


Report actual. Shall comply with any claims (-0%, +3%)
3.
product sizeweight
4. Costco Plastic Bag Warning
If plastic bags (of any thickness) with a perimeter of 14 inches or
greater are used in inner packaging, the following warning statement
Statement

must be printed on at least one side of each bag in English, French and
Spanish:

5. Lead In Surface Coating

6. Workmanship Level
Shall not exceed 600 ppm (0.06% by weight) total lead
?
?
?
?
No major defects
No components missing, malformed or fractured
No hardware missing
Smoothly ground welds, not over-ground and free of
pits and splatter


? No burrs
? No loose components and unsecured fastening where
rigidity is required
? In the case of wood (e.g. laminates) proper and
uniform adhesion
? No scratches, dents, cracks, marred or discolored
surface
? In the case of molded plastic, consistent and concise
form and no defects evidencing of overuse of mold.
? Finished edges and seams
? Accurate and consistent painting
? Components even in color, uniform clarity
? All seams and components in even alignment
? Accurate and consistent painting
? Components even in color, uniform clarity
Shall have no sharp edges or sharp points on any component
other than those required for functional use.
Plating finish must stay affixed – using a utility knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to
the grid. Remove to see if plating finish remains intact.

7. Sharp Points and Edges
8. Cross Cut Adhesion

9. Flammability
Materials
of Upholstery Must comply with California Bureau of Home Furnishings
Bulletin 116117
Shall meet the requirements intended to eliminate the possible
hazard that may be caused by changing clearances or
permanent entrapment and pinching of fixed openings.(<5mm
or >13mm)
Pour 25 mL. of boiling water and allow cooling. Dry surface,
Shall be no graying or spotting
24 Hours At -32° F And 140°F - No failure
10. Finger Entrapment
11. Resistance To Hot Water
11 Effects Of Extreme Temperature
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no
Components) corrosion or visual change.
13. Effects Of Humidity No change after 24 hours. @ 95% RH & 100°F
14. Stain Resistance- (Do not test on Various food materials – should resist permanent
picnic table racks) staining.( After 2 hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original)
10. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft
BBQ Sauce (original) Red Wine
15 Resistance to Scratching Marring
No scratching or marring of surface (3 cycles of 6” back and

Other Surfaces forth.) Conduct with and without levelers. Note if levelers
become bent or come off. Note any damage defects
(bentbroken levelers)
16. Caster Performance (If Supplied)
17. Rear Stability
Max 5 lb pull to move under 200 lb load
Min 35 Lbs. (30 Lbs. children) tipping force with a 173 Lbs.
(100 Lbs. children) weight placed on the seat (Strap). Force
is applied in rearward direction against 1inch obstruction.
Report result when seat is in minimum, midpoint and
maximum position
The chair is obstructed by 1 inch bar in the front base, tipping
force is measured in the 45° to the test platform. The tipping
force shall not be less than 40% of the total chair weight.
Min 10 degree with 150 Lbs. (Children 100 Lbs.) distributed
load, no tip-over
Min 20 Lbs. pull force after 150 Lbs. (Children 100 Lbs.)
distributed load on the seat, no tip-over
No structural failure or permanent deformation under 400
Lbs. (225 Lbs. children) static load for 60 minutes. For
multi seatback positions, report result when seat back is in
minimum, midpoint, and maximum positions for 20 minutes
each.
No failure under 300 Lbs. (135 Lbs. children) loading at edge
(6 In.)
18. Front Stability
(Excludes Barstools & Ottomans)
19. Tip Resistance (Stools Only)
20. Stability (Stools Only)
21. Base Durability
22. Front Seating Capability
(Excludes Barstools & Ottomans)
23. Impact Durability No structural breakage, max ? inch deformation when 225
(*If applicable – perform with and Lbs. (200 Lbs. folding chairs, 175 Lbs ottomans, 100 Lbs.
without cushion) children) test load free falls from 6 inch to the center of the
seat. For multi seatback positions, report result when seat

back is in minimum, midpoint, and maximum positions. If
chair has levelers, conduct test with levelers fully extended
then rotated inward two revolutions.
24. Back Pull Durability
25. Arm Strength Test (Vertical)
No failure at 100 Lbs. (60 Lbs. children) for 1 min. applied to
90° from back at 16 inch above the seat.
No permanent deformation at 300 Lbs. (90 Lbs. children) for
1 min. The vertical load is uniformly applied through a 5 inch
wide board across both arms – No failure deformation
No permanent deformation at 75 Lbs. (45 Lbs. children) for 1
min. The load is applied to the armrest horizontally at the
most forward point of the armrest area.
No failure or permanent deformation at 75 Lbs. (40 Lbs.
Child folding chairs) applied to each leg at 1 inch from the
end of the leg. Force is applied in four directions (Forward,
rearward, side and side) for 1 minute.


26．Arm Strength Test (Horizontal)
27. Leg Strength

36. Moisture Content (%) (Solid 8% - 12% (Do not test on MDF)
Wood Only)
37. Lightfastness




Class 4.0 @ 20 hrs - Test up to 5 majormain components
MTL SGS TEST LIST (8)
(Seating)

(Combines Adult and Children’s sizes,:Chairs, Barstools, Ottomans,)
Quality test standardmethod

ng DesignFeatures
ctions
Criteria

The actuality must keep consistency with the claim.

Results

Shall be included if necessary. Shall include assembly,
mounting, use, maintenance, cleaning and safety information
as required in the language(s) applicable to the destination
country(s) with no errors or spelling mistakes. Shall be easy
to follow and accurate.


Report actual. Shall comply with any claims (-0%, +3%)
3.
product sizeweight
4. Costco Plastic Bag Warning
If plastic bags (of any thickness) with a perimeter of 14 inches or
greater are used in inner packaging, the following warning statement
Statement

must be printed on at least one side of each bag in English, French and
Spanish:

5. Lead In Surface Coating

6. Workmanship Level
Shall not exceed 600 ppm (0.06% by weight) total lead
?
?
?
?
No major defects
No components missing, malformed or fractured
No hardware missing
Smoothly ground welds, not over-ground and free of
pits and splatter

? No burrs
? No loose components and unsecured fastening where
rigidity is required
? In the case of wood (e.g. laminates) proper and
uniform adhesion
? No scratches, dents, cracks, marred or discolored
surface
? In the case of molded plastic, consistent and concise
form and no defects evidencing of overuse of mold.
? Finished edges and seams
? Accurate and consistent painting
? Components even in color, uniform clarity
? All seams and components in even alignment
? Accurate and consistent painting
? Components even in color, uniform clarity
Shall have no sharp edges or sharp points on any component
other than those required for functional use.
Plating finish must stay affixed – using a utility knife, cut a
grid of 16 squares. Use 3M masking tape (#202), apply to
the grid. Remove to see if plating finish remains intact.
Upholstery Must comply with California Bureau of Home Furnishings
Bulletin 116117
Shall meet the requirements intended to eliminate the possible
hazard that may be caused by changing clearances or
permanent entrapment and pinching of fixed openings.(<5mm
or >13mm)
Pour 25 mL. of boiling water and allow cooling. Dry surface,
Shall be no graying or spotting
24 Hours At -32° F And 140°F - No failure
7. Sharp Points and Edges
8. Cross Cut Adhesion
9. Flammability
Materials
of
10. Finger Entrapment
11. Resistance To Hot Water
11 Effects Of Extreme Temperature
12. Resistance To Corrosion (Metal Shall withstand 24 hours in 1% salt spray (fog) with no
Components) corrosion or visual change.
13. Effects Of Humidity No change after 24 hours. @ 95% RH & 100°F
14. Stain Resistance- (Do not test on Various food materials – should resist permanent
picnic table racks) staining.( After 2 hours, remove)
1. French’s Mustard t2. Heinz Ketchup3. Ragu Spaghetti sauce
(original)
11. Folgers Instant Coffee 5. Welch’s Grape Juice6. Kraft
BBQ Sauce (original) Red Wine
15 Resistance to Scratching Marring
No scratching or marring of surface (3 cycles of 6” back and

Other Surfaces forth.) Conduct with and without levelers. Note if levelers
become bent or come off. Note any damage defects
(bentbroken levelers)
16. Caster Performance (If Supplied)
17. Rear Stability
Max 5 lb pull to move under 200 lb load
Min 35 Lbs. (30 Lbs. children) tipping force with a 173 Lbs.
(100 Lbs. children) weight placed on the seat (Strap). Force
is applied in rearward direction against 1inch obstruction.

Report result when seat is in minimum, midpoint and
maximum position
18. Front Stability
(Excludes Barstools & Ottomans)
19. Tip Resistance (Stools Only)
20. Stability (Stools Only)
21. Base Durability
The chair is obstructed by 1 inch bar in the front base, tipping
force is measured in the 45° to the test platform. The tipping
force shall not be less than 40% of the total chair weight.
Min 10 degree with 150 Lbs. (Children 100 Lbs.) distributed
load, no tip-over
Min 20 Lbs. pull force after 150 Lbs. (Children 100 Lbs.)
distributed load on the seat, no tip-over
No structural failure or permanent deformation under 400
Lbs. (225 Lbs. children) static load for 60 minutes. For
multi seatback positions, report result when seat back is in
minimum, midpoint, and maximum positions for 20 minutes
each.
No failure under 300 Lbs. (135 Lbs. children) loading at edge
(6 In.)
22. Front Seating Capability
(Excludes Barstools & Ottomans)
23. Impact Durability No structural breakage, max ? inch deformation when 225
(*If applicable – perform with and Lbs. (200 Lbs. folding chairs, 175 Lbs ottomans, 100 Lbs.
without cushion) children) test load free falls from 6 inch to the center of the
seat. For multi seatback positions, report result when seat
back is in minimum, midpoint, and maximum positions. If
chair has levelers, conduct test with levelers fully extended
then rotated inward two revolutions.
24. Back Pull Durability
25. Arm Strength Test (Vertical)
No failure at 100 Lbs. (60 Lbs. children) for 1 min. applied to
90° from back at 16 inch above the seat.
No permanent deformation at 300 Lbs. (90 Lbs. children) for
1 min. The vertical load is uniformly applied through a 5 inch
wide board across both arms – No failure deformation
No permanent deformation at 75 Lbs. (45 Lbs. children) for 1
min. The load is applied to the armrest horizontally at the
most forward point of the armrest area.
No failure or permanent deformation at 75 Lbs. (40 Lbs.
Child folding chairs) applied to each leg at 1 inch from the
end of the leg. Force is applied in four directions (Forward,
rearward, side and side) for 1 minute.


26．Arm Strength Test (Horizontal)
27. Leg Strength

36. Moisture Content (%) (Solid 8% - 12% (Do not test on MDF)
Wood Only)
37. Lightfastness Class 4.0 @ 20 hrs - Test up to 5 majormain components
? 包装测试
1． For all carton dimensions as usual:
Dimensions refer to the exterior of a carton, measured in inches of Length x Width x
Height. in inches (mm or m)
1.1 Length (L) is the longer side of the opening,
1.2 Width (W) is the shorter.
1.3 Height (H) is the length between the openings on either end.

1．。
一般的纸箱尺寸:
以纸箱外表面为例, 尺寸以英寸为单位: 长 X 寛 X 高, {mm 或 m},
1.1 长是外围的长边
1.2 宽是外围的短边
1.3高是两端外围之间的距离
2。Measure the weight of carton in pounds (kg)
2．测量纸箱重量, 单位为磅{千克}
3．Vibration Test Period.
3.1 ISTA-1A For Packaged Product 150 lb (68 kg) or less
Test Duration in Minutes
=
14,200 Vibratory Impacts .
Revolutions Per Minute (RPM)
3.2 ISTA-1B, 2B For Packaged Product Over 150 lb (68 kg)
Test Duration in Minutes = 11,800 Vibratory Impacts .
Revolutions Per Minute (RPM)
3.3 (For ISTA) Procedure
Stop the vibration test half way
Turn the packaging 90? (if possible)
If the packaging is too large, turn the packaging 180?
Recalculate the cycle time
3。震动测试时间
3.1 ISTA-1A, 150LB或150LB以下, 其震动时间=14,200次频率
3.2 ISTA-1B, 150LB以上, 其震动时间=11,800次频率
3.3 ISTA 测试过程
时间到一半时, 停止震动
如可能,将包装样品转动90度
如包装样品太大, 将包装样品转动180度)
重新计算震动时间
4．Drop test
4.1 FREE-FALL Drop Sequence
ISTA 1A (150 lb or less) 1 corner, 3 edges & 6 faces
(Most Fragile bottom corner, if not known, bottom corner diagonally opposite the
manufacturer’s joint)
ISTA 1B (more than 150 lb) 6 faces
4.2 Drop Height






Drop height inches
Shipping -1AISTA-1BMod. FedExRule 181
0-21303030
21-25243030
25-40243024
40-41 243018
41-61183018
61-76123018
76-8012241 8
81-100122412
100-15082410

over 1506126

4. 自由落摔测试顺序
4.1 ISTA 1A (150LBS或150LB以下) 1角, 三边, 六面
(底部最脆弱的角, 如无法确定, 就选接缝边的对底角)
ISTA 1B (超过150LBS) 六面
4.2摔箱高度

Drop height inches

Shipping -1AISTA-1BMod. FedExRule 181

0-21303030
21-25243030
25-40243024
40-41243018
41-61183018
61-7 6123018
76-80122418
81-100122412
100-1508 2410
over 1506126