关键词不能为空

当前您在: 主页 > 英语 >

建筑工程设计文件编制深度规定(带英文翻译)

作者:高考题库网
来源:https://www.bjmy2z.cn/gaokao
2020-10-27 14:26
tags:生产用英语怎么说

鄱-人教版英语八年级下册单词跟读

2020年10月27日发(作者:元宣)



《建筑工程设计文件编制深度规定》The depth of engineering design documentation
requirements 中“初步设计”建筑部分内容如下:

3 初步设计
3 Preliminary design
3.1 一般要求
3.1 General requirement
3.1.1 初步设计文件
3.1.1 Preliminary design document
1 设计说明书,包括设计总说明、各专业设计说明。
1 The design specification include general design specification and various
professional design specificatons.
2 有关专业的设计图纸。
2 For professional design drawings
3 工程概算书。
3 Woks on commission
注:初步设计文件应包括主要设备或材料表,主要设备或 材料表可附在说明书中,
或附在设计图纸中,或单独成册。
TIPS: Preliminary design documents should include the list of major equipment
or materials. List of major equipment or materials can be attached to the
manual or separate booklet.
3.1.2 初步设计文件的编排顺序
3.1.2 Preliminary design documents are organized as follows:
1 封面:写明项目名称、编制单位、编制年月。
1 Cover
2 扉页:写明编制 单位法定代表人、技术总负责人、项目总负责人和各专业负
责人的姓名,并经上述人员签署或授权盖章。
2 Title page : prepared by the legal representative 、overall responsibility for
technology、the total charge and the name of the professional person in
charge.
3 设计文件目录。
3 Design document directory
4 设计说明书。
4 Design specification
5 设计图纸(可另单独成册)。
5 Design drawing (can be separate from that into a book)
6 概算书(可另单独成册)。
6 Budget book (can be separate from that into a book)
注:1 对于规模较大、设计文件较多的项目,设计说明书和设计图纸可按专业成
册;
2 另外单独成册的设计图纸应有图纸总封面和图纸目录;图纸总封面的要求
见4.1.2条。


Tips: 1 For larger or more project design document , design specifications and
design drawings into a book can be professional.
3 各专业负责人的姓名和签署也可在本专业设计说明的首页上标明。
Tips:3
3.2 设计总说明
3.2.1 工程设计的主要依据
1 设计中贯彻国家政策、法规。
2 政府有关主管部门批准的批文、可行性研究报告、立项书、方案文件等的文
号或名称。
3 工程所在地区的气象、地理条件、建设场地的工程地质条件。
4 公用设施和交通运输条件。
5 规划、用地、环保、卫生、绿化、消防、人防、抗震等要求和依据资料。
6 建设单位提供的有关使用要求或生产工艺等资料。
3.2.2 工程建设的规模和设计范围
1 工程的设计规模及项目组成。
2 分期建设(应说明近期、远期的工程)的情况。
3 承担的设计范围与分工。
3.2.3 设计指导思想和设计特点
1 采用新技术、新材料、新设备和新结构的情况。
2 环境保护、防火安全、交通组织、用地分配、节能、安保、人防设置以及抗
震设防等主要设计原则。
3 根据使用功能要求,对总体布局和选用标准的综合叙述。
3.2.4 总指标
1 总用地面积、总建筑面积等指标。
2 其他相关技术经济指标。
3.2.5 提请在设计审批时需解决或确定的主要问题
1 有关城市规划、红线、拆迁和水、电、蒸汽、燃料等能源供应的协作问题。
2 总建筑面积、总概算(投资)存在的问题。
3 设计选用标准方面的问题。
4 主要设计基础资料和施工条件落实情况等影响设计进度和设计文件批复时
间的因素。
3.2.6 总说明中已叙述的内容,在各专业说明中可不再重复。

3.3 总 平 面
3.3.1 在初步设计阶段,总平面专业的设计文件应包括设计说明书、设计图纸、
根据合同约定的鸟瞰图或模型。
3.3.2 设计说明书
1 设计依据及基础资料
1)摘述方案设计依据资料及批示中与本专业有关的主要内容;
2)有关主管部门对本工程批 示的规划许可技术条件(道路红线、建筑红线或
用地界线、建筑物控制高度、容积率、建筑密度、绿地率 、停车泊位数等),以


及对总平面布局、周围环境、空间处理、交通组织、环境保护、文 物保护、分期
建设等方面的特殊要求;
3)本工程地形图所采用的坐标、高程系统;
4)凡设计总说明中已阐述的内容可从略。
2 场地概述
1 )说明场地所在地的名称及在城市中的位置(简述周围自然与人文环境、道
路、市政基础设施与公共服务 设施配套和供应情况,以及四邻原有和规划的重要
建筑物与构筑物);
2)概述场地 地形地貌(如山丘,水域的位置、流向、水深,最高最低标高、
总坡向、最大坡度和一般坡度等);
3)描述场地内原有建筑物、构筑物,以及保留(包括名木、古迹等)、拆除的
情况;
4)摘述与总平面设计有关的自然因素,如地震、湿陷性或胀缩性土、地裂缝、
岩溶、 滑坡与其他地质灾害。
3 总平面布置
1)说明如何因地制宜,根据地形、地 质、日照、通风、防火、卫生、交通以
及环境保护等要求布置建筑物、构筑物,使其满足使用功能、城市 规划要求以及
技术经济合理性;
2)说明功能分区原则、远近期结合的意图、发展用地的考虑;
3)说明室外空间的组织及其与四周环境的关系;
4)说明环境景观设计和绿地布置等。
4 竖向设计
1)说明竖向设计的依据(如城市道路和管道的标高、地形、排水、洪水位、
土方平衡等情况);
2)说明竖向布置方式(平坡式或台阶式),地表雨水的排除方式(明沟或暗管)
等; 如采用明沟系统,还应阐述其排放地点的地形与高程等情况;
3)根据需要注明初平土方工程量。
5 交通组织
1)说明人流和车流的组织,出入口、停车场(库)的布置及停车数量的确定;
2)消防车道及高层建筑消防扑救场地的布置;
3)说明道路的主要设计技术条件(如主干道和次干道的路面宽度、路面类型、
最大及最小纵坡等)。
6 主要技术经济指标表(表格略)
注:1 当工程项目(如城市居住区)有相应的规划设计规范时,技术经济指标
的内容应按其执行。
2 计算容积率时,通常不包括±0.00以下地下建筑面积。
7 提请在设计审批时解决或确定 的主要问题。特别是涉及总平面设计中的指标
和标准方面有待解决的问题,应阐述其情况及建议处理办法 。
3.3.3 设计图纸
1 区域位置图(根据需要绘制)。
2 总平面图
1)保留的地形和地物;


2)测量坐标网、坐标值,场地范围的测量坐标(或定位尺寸),道路红线、建
筑红线或用地界线;
3)场地四邻原有及规划道路的位置(主要坐标或定位尺寸)和主要建筑物及构
筑物的 位置、名称、层数、建筑间距;
4)建筑物、构筑物的位置(人防工程、地下车库、油库、贮 水池等隐蔽工程
用虚线表示),其中主要建筑物、构筑物应标注坐标(或定位尺寸)、名称(或编号)、
层数;
5)道路、广场的主要坐标(或定位尺寸),停车场及停车位、消防车道及高 层
建筑消防扑救场地的布置,必要时加绘交通流线示意;
6)绿化、景观及休闲设施的布置示意;
7)指北针或风玫瑰图;
8)主要技术经济指标表(表3.3.2),该表也可列于设计说明内;
9)说明栏内注写: 尺寸单位、比例、地形图的测绘单位、日期,坐标及高程
系统名称(如为场地建筑坐标网时,应说明其与 测量坐标网的换算关系),补充图
例及其他必要的说明等。
3 竖向布置图
1)场地范围的测量坐标值(或注尺寸);
2)场地四邻的道路、地面、水面,及其关键性标高;
3)保留的地形、地物;
4)建筑物、构筑物的名称(或编号)、主要建筑物和构筑物的室内外设计标高;
5)主要道路、广场的起点、变坡点、转折点和终点的设计标高,以及场地的
控制性标高;
6)用箭头或等高线表示地面坡向,并表示出护坡、挡土墙、排水沟等;
7)指北针;
8)注明:尺寸单位、比例、补充图例;
9)本图可视工程的具体情况与总平面图合并;
10)根据需要利用竖向布置图绘制土方图及计算初平土方工程量。

3.4 建 筑
3.4.1 初步设计阶段,建筑专业设计文件应包括设计说明书和设计图纸。
3.4.2 设计说明书
1 设计依据及设计要求
1)摘述设计任务书和其他依据性资料中与建筑本专业有关的主要内容;
2)表述建筑类别和耐火等级,抗震设防烈度,人防等级,防水等级及适用规
范和技术标准;
3)简述建筑节能和建筑智能化等要求。
2 设计说明
1)概述建筑物使用功 能和工艺要求,建筑层数、层高和总高度,结构选型和
对设计方案调整的原因、内容;
2)简述建筑的功能分区、建筑平面布局和建筑组成,以及建筑立面造型、建
筑群体与周围环境的关系;


3)简述建筑的交通组织、垂直交通设施(楼梯、电梯、自动扶梯)的布局,以
及所采用的电梯、自动扶梯的功能、数量和吨位、速度等参数;
4)综述防火设计中 的建筑分类、耐火等级、防火防烟分区的划分、安全疏散,
以及无障碍、节能、智能化、人防等设计情况 和所采取的特殊技术措施;
5)主要的技术经济指标包括能反映建筑规模的总建筑面积以及诸 如住宅的
套型和套数、旅馆的房间数和床位数、医院的门诊人次和住院部的病床数、车库
的停车 位数量等;
3 多子项工程中的简单子项可用建筑项目主要特征表(表格略)作综合说明。
4 对需分期建设的工程,说明分期建设内容和对续建、扩建的设想及相关措施。
5 幕墙工程、特殊屋面工程及其它需要另行委托设计、加工的工程内容的必要
说明。
6 需提请审批时解决的问题或确定的事项以及其它需要说明的问题。
7 必要的计算资料的说明简图。
3.4.3 设计图纸
1 平面图
1)标明承重结构的轴线、轴线编号、定位尺寸和总尺寸;
2)绘出主要结构和建筑构配件, 如非承重墙、壁柱、门窗(幕墙)、天窗、楼
梯、电梯、自动扶梯、中庭(及其上空)、夹层、平台、阳 台、雨篷、台阶、坡道、
散水明沟等的位置;当围护结构为幕墙时,应标明幕墙与主体结构的定位关系;
3)表示主要建筑设备的位置,如水池、卫生器具等与设备专业有关的设备的
位置;
4)表示建筑平面或空间的防火分区和防火分区分隔位置和面积,宜单独成
图;
5)标明室内、外地面设计标高及地上、地下各层楼地面标高;
6)标明指北针(画在底层平面);
7)标明剖切线及编号;
8)绘出有 特殊要求或标准的厅、室的室内布置,如家具的布置等;也可根据
需要选择绘制标准层、标准单元或标准 间的放大平面图及室内布置图;
9)列出各类建筑设计规范要求计算的技术经济指标(也可在说明中列出)。
10)标明图纸名称、比例。
2 立面图
应选择绘制主要立面,立面图上应标明:
1)两端的轴线和编号;
2)立 面外轮廓及主要结构和建筑部件的可见部分,如门窗(幕墙)、雨逢、檐
口(女儿墙)、屋顶、平台、栏 杆、坡道、台阶和主要装饰线脚等;
3)平、剖面未能表示的屋顶、及屋顶高耸物、檐口(女儿墙)、室外地面、等
主要标高或高度;
4)图纸名称、比例。
3 剖面图
剖面应剖在层高、层数不 同、内外空间比较复杂的部位(如中庭与邻近的楼
层或错层部位),剖面图应准确、清楚的标示出剖到或 看到的各相关部分内容,
并应表示:


1) 主要内、外承重墙、柱的轴线,轴线编号;
2)主要结构和建筑构造部件,如:地面、楼板、 屋顶、檐口、女儿墙、吊顶、
梁、柱、内外门窗、天窗、楼梯、电梯、平台、雨逢、阳台、地沟、地坑、 台阶、
坡道等;
3)各层楼地面和室外标高,以及室外地面至建筑檐口或女儿墙顶的 总高度,
各楼层之间尺寸及其他必需的尺寸等;
4)图纸名称、比例。
4 对于紧邻的原有建筑,应绘出其局部的平、立、剖面。

最后,建议你去建筑标准书店,买一本 中国建筑标准设计研究院 发行的 国家
建筑标准设计图集:《民用建筑工程建筑初步设计深度图样 05J802》,定价仅
39 元,含光盘一张。图集中有初步设计的说明书、图纸范本,对设计工作具有
参考价值。


2. Project Design


2.1 General Requirements
2.1.1 Project design documents

1 The design specifications include various professional design specifications and
investment estimation; for those professions involved with building energy- effective design,
the design specification shall include the special content related to the building
energy-efficiency;

2 The general layout and the building design drawings (for the urban district heating or
regional gas pressure-regulating station, professional thermal power design drawings shall be
provided, details are shown in Article 2.3.3);

3 The scenograph, bird's-eye view and model specified in the design commission or
design contract

2.1.2 Editing sequence of the project design document

1 Cover: project name, preparation units and preparation date

2 Title page: the name of the legal representative, general technical superintendent and
the general project superintendent of the preparation unit, and signed by the above person or
authorized with stamp;

3 design document directory;

4 design specifications;

5 design drawing;

2.2 Design Specifications

2.2.1 The design basis, design requirement and major technical economical index


1 The name and number of reference document related to the engineering design, such as
location and environmental assessment report, boundary line of land, project feasibility
research report, project approval issued by the relevant governmental competent department,
design specification or agreement;

2 The main regulations carried out by the design and the adopted primary standard
(including the standard name, number, era name and version number);

3 design basis information, such as meteorology, topography, hydrogeology, basic
earthquake intensity and regional location;

4 Briefly indicate the requirements of the relevant government departments to the project
design, such as requirements on aspects like general layout, environment coordination and
architectural style. When the city planning departments confines the building height, the
control height of the buildings and structures shall be mentioned (including the maximum and
minimum altitude limitation);

5 briefly introduce the content and scope designed according to the commission of the
construction unit, including the supporting situation of the functional project and equipment
or facilities;

6 The project scale (such as the total construction area, total investment and
accommodation population), project design scale grades and design standards (including the
structure's design life, building fire type, fire-resistant grades, fitment standards);

7 The main technical and economic indexes, such as the total construction area, total
floor area and categorized building area (with list of building area of both aerial portion and
underground portion respectively), total building base area, total greenfield area, floor area
rate, building density, green rate, parking berthing capacity (including indoor, outdoor,
ground and underground), floors of main building or core building, floor height and overall
height and other indexes; according to different architectural features, major technical and
economic indexes reflecting the project scale shall also be indicated, such as residential
dwelling size, number, building area, floor area, guest room number and bed number of the
hotel building, out-patient visits number and sickbed number of the hospital building, and
other indexes; when the engineering project (such as urban residential area planning) is
limited by other corresponding design codes or standards, the technical and economic indexes
shall also comply with them thereof.

2.2.2 Design specification of general plane

1 summarize the features of the site actuality, peripheral environment condition and
geological or morphological features, elaborate the idea intent and layout features of the
general planning, and the physical measures adopted in aspects of vertical design, traffic
organization, fire protection planning, landscape planting and environmental protection.

2 explain the general considerations on primary planning, construction stages, the
preservation, utilization and renovation (reconstruction) of original buildings and old trees or
rare woods

关于中秋节的日记-老虎钳


massage是什么意思-佛山属于哪个省


东方英语-在任何时候英语


什么是礼-丫鬟怎么写


教堂英文-在线日语学校


高中物理磁场公式-日语初级听力下载


什么是主语谓语宾语定语状语补语-simplicity


弥高的意思-when怎么读英语



本文更新与2020-10-27 14:26,由作者提供,不代表本网站立场,转载请注明出处:https://www.bjmy2z.cn/gaokao/429419.html

建筑工程设计文件编制深度规定(带英文翻译)的相关文章