关键词不能为空

当前您在: 主页 > 英语 >

注塑成型不良点英文翻译

作者:高考题库网
来源:https://www.bjmy2z.cn/gaokao
2020-10-29 12:37
tags:翻译英语怎么说

旮旯拼音-哥哥的哥怎么写

2020年10月29日发(作者:侯喜瑞)


注塑、模具专业英语
Surface Appearance 外观
Glossinessgloss finish 光洁度、粗糙度
Matt finishmatt surface 毛面
Glass fiber rich surfaceglass emergence on the surface 玻纤外露、浮纤
Bloomingsurface blooming 表面析出
White patches on surface 表面白斑
Silver markssilver streak 银纹
Splay mark 水纹、料花
Flow mark 流纹
Brittlebrittleness 脆、脆性
Bubblestrapped gas 气泡困气
Void 孔、气泡
Burn marks 烧伤
FR failed 阻燃不合格
Flame rating V-2 阻燃等级V-2
Poor dispersion 分散不好
FRPTFE …agglomerates etc
Pellet porous 颗粒料孔隙、
Low impacttensile strength etc 低冲击强度拉伸强度等
High flowfiller content etc 高流动性过度填充
Longsfinesdoubles 长粒碎屑连粒
Poor cut 粒形不好
阻燃剂PTFE…结块


Bristlevoids 表面有小气泡孔
Glass bundles 纤维结团
Product was rejected due to 产品不能接受因为…
High moisture level 高水分、高湿度
Warpagewarped 翘曲变形
Shrinkageshrink 收缩收缩率
Sink marks 凹陷、缩水
Short shotshort molding 打不满、欠注
Distortion 变形
Over dimension 尺寸过大
Under dimension 尺寸过小
Flashing 飞边、披锋、溢边
Discoloration 变色
Off color 颜色差异
Flow rate 流动速率
Viscousviscosity 粘性的、粘的黏度
High flow 高流动
Low flow 低流动
Sticky 粘的,粘性的
Sticking core 粘后模,粘模芯
Sticking sprue 粘水口
Sticking cavity 粘前模
Mold release(agent) 脱模(剂)


Antioxidant 抗氧剂
Flame retardant agent 阻燃剂
Heat stabilizer 热稳定剂
Chopped glass fiber 短切玻纤
Roving glass fiber 粗纱长玻纤
Glass beads 玻璃微珠
Milled fiber 碾磨纤
Molybdenum disulfidemolyMoS2 二硫化钼
Colorant 着色剂
Pigment 颜料
Dye 染料
Accepted product specification 接受产品规格
Approved our product 认可我们的产品
Re-set spec 重新定标准
Add in extra … 添加多一点…
Reduced … content 减少…含量
Droppedreduced … by x% 减少…含量…%
Confirmed color standard 确认颜色标准
Approved color standard 认可颜色标准
Re-confirmed color standard 重新确认颜色标准
Qualified our product 认可我们的产品
Undergoing heat aging test 在做热老化实验
Product is under testing 产品在测试当中


Received first order 接了第一个定单
Expected to finish by … 预计在…完成
Expected order is xMT 预计定单量…吨
Estimated annualmonthly consumption 预计年月用量
模具方面:
Ejection system 顶出系统、脱模系统
pin 顶针、推杆
spring 弹簧
Gate type 浇口类型
sprue 主流道
runner 分流道
cavity 模腔
Sprue gate 直浇口
Pin point gate 点浇口
Tab gate 护耳浇口
Fan gate 扇形浇口
Tunnel or submarine gate 潜伏式浇口
Jump gate 跳跃式浇口
Diaphragm gate 片状浇口
Ring gate 环形浇口
The cavity of the mould 模腔
Heated cylinder 加热料筒
Surface finish 表面光洁度


Sink mark 缩水
Air trap 困气
Gas trapped 气体困着,困气
void 空隙,孔
galling 烧焦
Weld line 熔接痕,熔合线
Drag mark 划伤、脱模痕
Scratch mark 模具刮花
Deformed warp 变形
Ejector not returned 顶针不回位
slide 滑块、行位
streak 波纹、条纹、色痕
delamination 分层
Jetting mark 喷射痕
Gate mark 浇口痕
rib 筋、加强筋、骨位
boss 凸台、凸起、凸痕
Melt flow length 熔体流线长度
Ejector plate 顶针板
Stop pin 限位销
Push rod 推杆、顶针
Push back pin 复位杆
Ejector guide pin 顶针导柱


Cold-slug-well冷料井、冷料穴
plate 模板
Ejected mark 顶痕,顶白
nozzle 喷嘴
Surface defect 表面缺陷
Air vent 排气口
Filling uneven 走胶不平衡、进胶不平衡

仙女英文-召唤读音


怯生生-大宛国


leam-Lorelei


伴侣怎么读-次第的意思


stuffed-百特英语


downtoearth-alga


新火-踵见


5210是什么意思-太阳英语怎么写



本文更新与2020-10-29 12:37,由作者提供,不代表本网站立场,转载请注明出处:https://www.bjmy2z.cn/gaokao/430747.html

注塑成型不良点英文翻译的相关文章