gauge是什么意思err for sp flash

2021年1月19日发(作者：amco)
Phone is totally dead


Message: Phone no longer responds to power button

Solution: Follow this guide @
/


Phone still not working after flashing


Message: Phone still stuck at Bootlogo or Bootloop

Solution:
* Ensure there's a formatted SD card in the phone before flashing
* Give up to 5 minutes because first boot takes time
* Boot the phone into recovery mode then wipe data / factory reset
* Remove the battery for 30 seconds then slot back in
* Try a firmware upgrade . use MTK droid tools version 2.3.0 to backup usrdata & cache or
copy then from the clockworkmod backup
* Try a firmware / ROM from another source

Phone shows white screen, strange colors or divided screen after flashing


Message:
You
can
see
the
phone
responding
to
buttons
and
making
sound
but
all
is
blurred by white screen

*
Solution:
The
ROM
/
Firmware
you
flashed
is
incompatible,
get
from
another
source
(especially , and / )

Phone automatically disconnecting during flashing


Message: The phone makes the disconnecting sound just as flashing begins, interrupting
the process

Solution:
* Try a different USB cord, USB port & PC
* Try holding down the Volume decrease (you could try volume increase or both) while
connecting the phone to PC for flashing

* Launch Device manager (Right-click My Computer > Select Manage)

* Connect the phone to the PC via a USB cord, Device manager should refresh

* Take note of what the phone is detected as (often as Unknown or Mediatek under Other
devices)

* Right-click whatever the phone is detect as and select Update Driver Software...

* Select Browse my computer for driver software

* Select Let me pick from a list of device drivers on my computer

* Click Next

* Click Have Disk

*
Proceed
with
the
Mediatek
(VCOM)
driver
installation
steps
described
at
/

and
click
Yes
if
you
get
an
Update
Driver
warning

Sp Flash tool remains at 0%


Message: Phone only shows charging sign

Meaning: Necessary drivers have not been successfully installed on the PC

Solution:
* Follow this guide @
/

to manually install vcom
drivers
*
If
you
have
installed
VCOM
drivers
but
the
phone
is
still
only
charging
then
Launch
Device manager (Right-click My Computer > Select Manage)

* Connect the phone to the PC via a USB cord, Device manager should refresh

* Take note of what the phone is detected as (often as Unknown or Mediatek under Other
devices)

* Right-click whatever the phone is detect as and select Update Driver Software...

* Select Browse my computer for driver software

* Select Let me pick from a list of device drivers on my computer

* Click Next

* Click Have Disk

*
Proceed
with
the
Mediatek
(VCOM)
driver
installation
steps
described
at
/

and
click
Yes
if
you
get
an
Update
Driver
warning

Error 5054


Message:
BROM ERROR S_DL_GET_DRAM_SETTINGS_FAIL (5054)

Meaning: The files you're trying to flash do not belong to or are not compatible with the
phone you're trying to flash them to

Solution:
* Ensure you're using the correct files. If you're sure they are, then try formatting before
flashing again

Initialize scatter failed


Message: Error: Initialize scatter file failed. Please check the scatter file name you load is
legal

Meaning: SP Flash tool doesn't accept the name format of your scatter file

Solution:
* Ensure the scatter file wasn't renamed. If you're certain it wasn't, try a higher version of
SP Flash tool

Error 8038


Message: Error 8038! Android download
pmt is ready and layout has been changed

Meaning:
SP
Flash
tool
is
having
trouble
writing
to
certain
partitions
due
to
some
incompatibility

Solution:
* Format the phone in SP flash tool (Do not format Bootloader) then try flashing the files
again using Download
* If Download doesnt work then do a firmware upgrade
*
If
the
MTK
backup
contains
more
than
one
scatter
file,
retry
flashing
with
the
other
scatter file.
* If that isn't feasible, try formatting first or use firmware upgrade
* If that doesn't work, open the scatter file using Notepad++ and change __NODL_FAT to
FAT by removing


Error 4032


Message: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail


Meaning: The firmware you're trying to flash is either not compatible with your device or
you have selected the wrong flashing settings


Solution:
* Ensure that the file(s) you're trying to flash are actually for your exact phone model
* Ensure you tick the boxes for only the files present in the ROM you're about to flash
* Probably have the wrong driver installed. Uninstall vcom,
preloader and MTK drivers
using
usb
deview
then
manually
re-install
using

/

* Delete the sp flash tool folder then re-extract

* Ensure the phone is switched off (with battery still inside) before connecting to PC for
flashing.

*
If
that
doesn't
work,
keep
holding
down
the
volume
decrease
button
just
before
connecting the phone to PC for flashing (you could try volume increase , power + volume
decrease or power + volume increase).
* Consider using the latest version of Sp Flash tool
* Format the phone before trying to flash the file(s) again


Error 5056


Message: BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069)


Meaning:
The size of a file is larger than the available / possible partition size

Solution:
* Ensure that the file(s) you're trying to flash are actually for your exact phone model
* Try another stock ROM
* Change the phone's emmc chip

Error 4001



Message: S_FT_DA_NO_RESPONSE or Da didn't send response data to FlashTool!

Meaning: SP flash tool is having difficulty communicating with the device

Solution:
* Change the USB-port
* Run SP flash tool as Admin
* Ensure to install the correct drivers (see
/
)
* Try another PC and USB cord
* Ensure the phone is switched off with a charged battery inside when connecting to the
PC for flashing

Sp flash tool was successful but phone's calibration doesn't work


Message: Soft keys and touch screen don't work / respond

Solution:
* Edit the scatter file using Notepad++ and remove NODL__
(or set is_download: false to
is_download: true
)
in
front
of
the
items you
have
in
the
backup
folder
but
aren't
listed
when you load the scatter file in SP flash tool. This way, these items will become listed
when
next you load the scatter file (after saving of course) and therefore flashable

Error 4008


Message: BROM ERROR : S_FT_DOWNLOAD_FAIL (4008)


Meaning: SP Flash tool encountered an error while attempting to flash files

Solution:

* Ensure the battery is in the phone and the phone is switched off before connecting for
flashing
* Try using a higher version of SP flash tool
* Change the USB cord and port or PC
* Use the format option then download in SP flash tool

Error 3149


Message: BROM ERROR : S_DA_SDMMC_WRITE_FAILED (3149)

Meaning: SP Flash tool was unable to flash files to the phone

Solution:

* Ensure to run the latest version of SP flash tool as Administrator
* Format first then Download
* Don't tick a box with an unspecified / empty file path
* Ensure the phone is switched off (with a well charged battery in it ) before connecting to
PC for flashing
* Try a different PC
* Try a different ROM
* Try a different USB cord
* Try formatting the phone first before flashing files to it

Error 3168


Message: BROM ERROR: S_CHIP_TYRE_NOT_MATCH(3168)

Meaning: Sp flash tool believes there's a mismatch between the information provided in
the scatter file and the phone's info.

Solution:

* Ensure you're using the ROM for the exact phone model
* Try a higher version of SP flash tool
* Ensure to install the correct drivers for the phone on the PC

Error 2004


Message: BROM ERROR : S_FT_DOWNLOAD_FAIL (2004)

Meaning: There was an interruption in the communication between SP flash tool and the
device

Solution:

* Take out and reinsert the battery
* Try using a different USB cord, port and PC
* Right-click flash_ > Select Properties > Select Compatibility > Set to Windows
XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
* Try a different USB cord
* Try a different port on the PC or another PC
* Ensure the battery is well changed and inside the switched off phone before connecting
to PC for flashing

USB device not recognized


Message: USB device not recognized prompt at system tray after connecting
the phone
to PC

Meaning:
The
PC
is
having
problems
communicating
with
the
phone
(often due
to
interruption, hardware or driver problems)

Solution:
* Follow the guide @
/

* Try a different USB cord, PC port or PC

Error 1013


Message: BROM ERROR:S_COM_PORT_OPEN Fail(1013)

Meaning: SP flash tool encountered an error while attempting to communicate with the
phone via the target port

Solution:
* Try using a different port on the PC
* Try a different version of SP flash tool
* Install VCOM drivers using

/

*
Ensure
the
phone
is
switched
off
with
battery
inside
before
connecting
to
the
PC
for
flashing
* Try using a different PC
* Try changing the USB cord
* Ensure the phone's USB port isn't damaged


Error 2020


Message: BROM ERROR : S_BROM_CHKSUM16_MEM_RESULT_DIFF (2020)

Meaning:
SP
flash
tool
encountered
a
problem
moving
the
files
to
be
flashed
into
the
phone's internal SRAM

Solution:

* Use the latest version of SP flash tool
* In SP flash tool, navigate to Options > Option > Connection > Battery. Set it to

battery

* Use the Format all + Download option
* Hold
both
volume
buttons before connecting
to the
PC for flashing
and
release
once
flashing begins


Error 5007


Message: BROM ERROR : S_FTHND_FILE_IS_NOT_LOADED_YET (5007)

Meaning: You're trying to flash an item with an unspecified path (no file selected for the
ticked item/box)

Solution:
* Ensure the scatter file is in the same directory as the other file(s) to be flashed
* Untick any item whose file you do not have or whose path is not specified; yet, is ticked /
selected for flashing

Error 4010


Message: BROM ERROR : S_FT_FORMAT_FAIL

Meaning: The blocks map in the scatter file doesn't match the phone's partition sizes

Solution:
* Try using the latest version of Sp flash tool
* Try using another firmware for the exact phone model

Error 3182


Message: BROM ERROR: S_STORAGE_NOT_MATCH (3182)

Meaning: The ROM your're trying to flash is not compatible with the target device

Solution:
* Download the ROM for the exact phone model you're trying to flash
* Ensure to install VCOM drivers on the PC
* Don't tick any box (after loading the scatter file) without a file path / whose corresponding
file has not been automatically or manually loaded.

Error 6012


Message: BROM ERROR: S_SECURITY_SF_CODE_COMMAND_FORBIDDEN (6012),
MSP ERROR CODE: 0X00

Meaning: The Download-Agent being used is incompatible with the phone

Solution:
* Set Download- Agent to MTK_AllInOne_

Error 1042


Message: BROM ERROR: S_TIMEOUT (1042)

Meaning: The flashing process took too long so SP flash tool encountered a timeout

Solution:
* Try flashing one file at a time
* Use the latest version of SP flash tool
* Try using a different PC and USB cord
* Try Infinix Flash tool @
/


Error 2


Message: BROM ERROR: ?? (2)

Meaning: SP Flash tool was unable to communicate with the phone

Solution:
* Try using a different PC (preferably Windows 7 or lower)
* Install the correct VCOM drivers for your PC's OS and architecture (32 or 64 bit)
* Try another USB cord

Error 2005


Message: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)

Meaning: The device attempted to power on before SP flash tool could flash files to it

Solution:

* Ensure the battery is well charged
* Take out and reinsert the battery
* Try using a different USB cord, port and PC
* Right-click flash_ > Select Properties > Select Compatibility > Set to Windows
XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
* Try a different USB cord
* Try a different port on the PC or another PC
* Ensure the battery is well changed and inside the switched off phone before connecting
to PC for flashing
* Do not hold any button when connecting to PC

Error 4058


Message: BROM ERROR: S_FT_GET_MEMORY_FAIL (4058)

Meaning: SP flash tool was unable to locate the partition you're trying to flash to