insideout快艇模型制作

2021年1月19日发(作者：clothes怎么读)
一艘快艇模型制作

快艇
模型
是赛艇最纯净的形式。

他们很少或没有做作的规模，而是是一个完全功能对象，
该函数存在的最终速度。


快艇模型，当减小到其本质，是举行了简单的棍子夫妇一起三盒。

然而， 他们似乎是一条
船，
船模
型
制作
一些愿意尝试。

这是否是因为他们不上诉从美学的角度，
或者是因为他们被
认为是太难以建立，我不能说。

这份简短的文章是不是如何
设计
一个快艇模型，或者如何建立一个具体的船。

这是一个在
技术
和材料我用它来建立我的支腿的概述。

希望它会激励你试试看！


The Kit
I start off with a minimal kit of parts cut from thin ply. I mark out one of the tub sides on a sheet of
ply, then cut this out. Using this as a template, I double-side glue it to another piece of ply then cut
out the second tub side. Repeat for the sponson templates.
该工具包

我开始了与来自薄层切割部件最小的套件。

我标记出的层上表中的一个浴缸边，然后把它
砍下来。

作为一个模板，我双面胶水，另一股则削减了第二个浴缸方片。

为
sponson
重
复模板。


A kit of parts to make a 12 cell, 700BB-powered outrigger.
I've cut lightening holes in the balsa doublers for the tub sides.
Lining Up
In order for the sponsons and the tub to line up correctly when assembled, the holes for the carbon
sponson booms must be drilled accurately. This is a task for a pillar drill. If you want to do this by
hand, then good luck!
试剂盒的零件，使
12
个细胞，
700BB
供电支腿。

我剪了减轻在浴缸两侧的轻木倍增器漏洞。

排队

为了使
sponsons
和浴缸排队正确装配时，为碳
sponson
繁荣钻的孔必须准确。

这是一
个支柱演习任务。

如果你想用手做了，那么祝你好运！


Sponson templates and tub sides double-side taped together for drilling.
Sponson
模板和浴缸边双面钻孔一起录音。


With the tub sides and sponson profiles double-side taped together along their respective datum
lines, drill the holes using a sharpened piece of brass tube mounted in a pillar drill.
随着浴缸边和录音一道沿着各自的基准线
sponson
概况双面，钻洞用削尖的黄铜管件安 装
在支柱演习。



Drilling the sponson templates and tub sides to accept the sponson booms.
Making the tub
With the holes drilled, carefully peel apart the tub sides and sponson profiles. Sand the insides of
the tub sides with medium-grade abrasive paper to remove both the plywood release agent and any
glue residue from the double-side tape. Coat each balsa doubler in turn with medium-thick cyano
superglue and glue to its respective tub side, wiping away any excess. When the cyano has cured,
carefully sand flush and square. Return the tub sides to the pillar drill and punch out the balsa over
the holes in the ply.
Using your engineer's square, carefully transfer and mark the location of each of the bulkheads on
the balsa lining. Take each bulkhead in turn and cyano superglue to the inside of one of the tub
sides, using the engineer's square to ensure each is glued perpendicular to the tub
side. Add the
1/16th

钻
sponson
模板和浴缸边接受
sponson
繁荣。

使浴缸

随着孔钻，小心剥离，除了浴缸边和
sponson
型材。

沙与中档砂纸浴缸两侧的内脏都去
除胶合板脱模剂和任何来自双面胶带胶水残留物。

外套每个中等厚氰基强力胶和胶其各自
的浴缸侧面转向巴尔萨倍，擦去多余的。

当氰基已治愈，
仔细冲洗砂和方形。

返回浴缸两
侧的支柱和打孔钻了多年来在轻木层孔。

使用您的工程师广场，仔细转移，标志着轻木衬对舱壁的每一个位置。

每个转弯，采 取强
力胶氰基舱壁到双方的一个浴缸内，用工程师的广场，以确保每个被粘在浴缸边垂直。
< br>添
加
1/16th
“
以同样的方式重复铺设横梁上的其他浴缸边的过程 。
：


Glueing the bulkheads using an engineer's square, cyano and kicker.

粘合用工程师的舱壁广场，氰基和踢球。


All bulkheads (except for motor mount) now in..

所有舱壁（除电机安装）现在英寸


Both sides of the tub joined together.
Take a length of 1/4
into the corners of each bulkhead as a fillet piece. Glue these with thin or medium cyano and trim
with the razor saw.

双方的浴缸结合在一起。

取
1 / 4
“
巴尔沙三角形和 切段长度为一到每个角落里脊肉一块舱壁上胶长度选择合适的短。
薄或中等氰胶这些和修剪剃刀看到的。


Balsa fillets for each bulkhead.
With the tub sides and bulkheads glued together, cut a block of pink foam to fit into the nose of the
tub. It needs to be a good fit, not too tight, such that it forces the tub sides apart, nor too loose so
the tub sides are drawn together, but a snug, sliding fit that does not distort the tub. Glue the block
in place with either five minute epoxy, or foam-safe cyano. When the glue has cured, fire up your
small hwc bow and trim the foam nose-piece flush.

巴尔沙鱼片每个舱壁。

随着浴缸边和舱壁粘在一起，切粉红色泡沫块，以适应进入浴缸鼻子。

它需要一个不 错的
选择，不要太紧张，这样，它迫使双方在浴缸外，也不能太松，因此浴缸两侧画在一起，而
是一个舒适，滑动不适合扭曲浴缸。

在与胶或环氧树脂五分钟，或泡沫安全氰基座。

当胶
水已治愈，火了你的小
hwc
弓和修剪泡沫鼻片冲洗。


Pink foam nose section, glued with 5 minute epoxy.

粉红色的泡沫机头部分，用
5
分钟环氧树脂粘合。


Pink foam nose section trimmed with hot wire, needs sanding.
Take your sanding block and sand the top and bottom of the tub to flush off the bulkhead edges,
the balsa fillets and the foam undercut on the nose piece. Be careful not to snag the edges of the
bulkheads when sanding.
NOTE:
When
sanding
any
part
of
the
boat,
be
extremely
careful
to
keep
all
edges
as
sharp
as
possible, unless noted otherwise.
粉红色的泡沫机头部分用热丝修剪，需要打磨。

把你的砂块，砂的顶部和浴缸冲洗过的舱壁边缘的底部，轻木和泡沫削弱鱼片鼻子上一块。

要小心，不要阻拦舱壁的边缘时，打磨。

注意：当任何船打磨的一部分，是非常小心，尽可能保持锋利的边缘，除非另有说明。


Deck with hatches marked out and scored, and tub floor.
Cut a piece of 32nd/0.6mm ply to size for the tub floor, leaving it oversize by a few mm on the
long
edges
and
transom,
and
oversize
by
5-6mm
where
it
curves
upwards
over
the
foam
nose-piece. It is vital that you place the tub on a truly flat surface when gluing the floor, as it is
very easy to introduce a warp at this point. With the tub positioned over the floor, run thin cyano
into the join followed with a quick squirt of kicker. Glue up to the the most forward bulkhead.

甲板舱口出来，并取得显着，地板和浴缸。

切下一块来的
32nd/0.6 mm
层楼面面积的浴缸，任由一个超大的长边和横梁几毫米，和
特大型
5 - 6mm
的地方曲线的泡沫鼻子件以上。

至关重要的是，你放在平坦的表面，当
一个真正的胶合地板的浴缸，因为它是非常容易引入在这一点上的偏差。

随着在地板上放
置的浴缸，跑进参加带有快速起脚之后薄喷氰基。

胶到最前沿舱壁。


Gluing the floor with thin cyano.
Ready
some
strips
of
masking
tape
then
mix
up
some
epoxy
(don't
use
foam- safe
cyano
here).
Peel back the tub floor from the foam nose-piece and apply a coat of epoxy with a spreader made
from a scrap of ply or balsa. Hold the tub floor to the foam with strips of masking tape. When
fully
cured,
use
your
razor
plan
to
trim
the
excess
away,
finishing
with
the
sanding
block. The
overlap on the nose should be trimmed with the large engineer's square, leaving a small overlap
that can be feathered by sanding.
Cut strips of 1/4
the floor. I like to use the mitre block to make the corners mitre together. This is not necessary for
strength, I do it purely for the sake of neatness. Repeat this process where the deck will meet the
sides,
leaving
these
fillets
slightly
proud
of
the
tub
and
sanding
back
flush
when
the
glue
has
dried.

粘合薄氰基发言。

准备一段胶带再拌入一些环氧树脂（不使用泡沫安全氰基这里）一些带。

剥离后的泡沫从
鼻子件浴缸地板，适用于从股或轻木废料做了吊具的环氧树脂涂层。

保持地板到浴缸与胶
带带泡沫。

当完全固化后，用你的剃刀计划削减多余的了，与砂块整理。

重叠的，应与大
工程师广场修整鼻子，留下一小部分重叠，可以通过打磨羽毛。

1 / 4
“
巴尔萨三角部分切条和胶水把那里的浴缸底部的两侧满足发言。我喜欢用 斜切角块，
使迈特在一起。
这不是必要的力量，
我这样做纯粹对于整洁的缘故。重复此 过程，
其中会遇
到的甲板两侧，使得这些鱼片稍稍浴缸骄傲和砂光反冲洗时，胶水干。


Adding balsa fillets to strengthen where the floor and sides meet.
Cut another piece of ply, oversized per the tub floor, for the deck. Repeat the gluing process of
cyano
up
to
the
bulkhead
behind
the
foam,
finishing
with
epoxy.
Trim
and
sand
the
excess
as
before. Cyano glue a piece of scrap 32nd/06mm ply over the transom, trim and sand flush with the
sides.
Some designs of outrigger I've seen don't have a deck as such. All my designs always have decks
with hatch openings as adding a deck vastly increases the torsional rigidity of the boat and gives
extra area for taping the hatches which helps keep the inside of the boat dry.
The positions for the hatch openings can be determined in advance and marked then scored on the
deck before the deck is glued to the boat, or you can glue the deck on and then identify by feel
through the ply deck where the bulkheads are and mark out hatches to suit.
Decide the extent of your hatch openings and mark using square and rule. As a guide, leave
10mm either side of a bulkhead and 15mm off the tub sides to give plenty of tape-down area
for the hatches. Use a hole stencil to mark radii in the corners of each hatch opening, then cut
out using your craft knife. Roughly cut across each corner
, leaving enough material behind to
sand a neat radius. To do this, take a piece of abrasive paper and wrap around a piece of
8-10mm dowel. Finish by sanding the edges of each opening to remove splinters.


添加巴尔沙鱼片，以加强那里的地板和侧面满足。

再降的层块，每楼层的浴缸超大的甲板。

重复氰基胶合处理多达泡沫背后的舱壁，与环氧
整理。

修剪和沙子像以前一样多。

氰基胶水一块废弃
32nd/06mm
在横梁层，修剪和砂
两侧平齐。

支腿一些我见过的设计并没有因为这样的甲板。

所有我的设计总是与添加甲板大大增 加船
的抗扭刚度，并给出录音舱口这有助于保持船的干额外的面积内舱口甲板。

在舱 口的位置可以事先确定，
标志着然后在甲板上取得了前甲板粘在船上，
或者你可以在甲
板上胶，然后确定通过层甲板的感受那里的舱壁和标记出舱口，以适应。

决定你的舱口和使用方和规则标记的程度。

作为一个指南，给
10mm的任一舱壁和关闭
的浴缸，让双方
15
毫米的磁带式地区大量的舱口侧。

使用一个洞模具，以纪念在每个舱
口的角落里，半径，然后切出使用工艺刀。

大约贯穿每个角落，留下一个整洁的砂半径足
够的材料。

要做到这一点，需要大约
8 - 10mm
的木钉，一块砂纸和包装件。

完成了打
磨每个开口边缘消除碎片。


The almost finished tub, with the deck added and the hatches cut out.
Return the almost finished tub to the pillar drill. Using your brass tube bit, core through the foam
nose-piece. Set the tub aside for the moment and turn to...
The Front Sponsons
Cut two blanks from a sheet of pink foam. Sand the wire-cut faces to remove the
mark a datum line parallel from one face on each blank.
Coat one face of each sponson profile in turn and glue to its respective blank. When cured, core
out the sponson boom holes on the pillar drill. Cut two lengths of brass tube long enough to thread
through both blanks, thus holding them together for the next operation, which is to hwc around the
sponson profile. Don't allow the hot wire to run off at the ends of each run; instead, as the wire
nears the end of a cut, pull it up and away sharply into the waste. The ridges left can be sanded
flush afterward.

几乎完成了浴缸，与甲板添加和切出舱口。

返回基本完成浴缸的支柱演练。

使用您的黄铜管位，
通过泡沫鼻片的核心。

将浴缸预留时
刻，转向
...

该阵线
Sponsons

从切两片粉红色泡沫空白。

砂 线切割面删除
“
特约
”
，然后标记从一个空白的脸在每个基准
线平行 。

外套一面对挨个和胶水其各自的空白
sponson
轮廓。

固化后，指出了在柱子上的洞钻
sponson
繁荣的核心。

切两 足够长的铜管坯都通过螺纹长度，
从而把它们穿在一起的下一
个操作，这是
hwc围绕
sponson
轮廓。

不要让热线运行在每次运行的两头切掉，而 是作
为导线接近一个切底，拉了起来，消失在废物急剧下降。

脊左可打磨后冲洗。


Sponson templates and foam blocks.
Carefully sand the two blanks together to remove the foam undercut, then separate. Glue, using
foam-safe cyano, the bottom sheet, then the top sheet, feathering the nose of each as necessary.
Cut a temporary cutter guide from 1/16th ply to give the desired anti-trip angles on each sponson.
When you have hwc the anti-trips, sand and sheet over, then cut the chamfer on the outside edge
of sponson. Sand and sheet over the bevel. Finally, sand the transom and cyano glue a ply capping
piece in place, sanding the excess flush with the sides.

Sponson templates and foam blocks.

仔细沙两个空白，共同消除泡沫削弱，然后分开。

胶水，用泡沫安全氰基，底表，然后面
层，
羽化每个必要的鼻子。

从
1/16th
切刀具引导层临时给每个
sponson
所需的反角行程。< br>
当你有
hwc
反人次，
沙子和片以上，
然后切对
s ponson
外边缘倒角。

在沙锥和板材。

最
后，沙的横梁和氰基胶水层覆盖在一块地方，与双方打磨多余的冲洗。


Templates glued to blocks, keyed with brass tubes.

粘块模板，使用铜管键入


Initial profile hwc to shape, trimmed to accept balsa leading edge.

初始配置文件
hwc
造型，修剪接受巴尔沙领先的优势


Balsa leading edges sanded flush.

巴尔沙前缘打磨冲洗


Ply sheeting to sponson tops.

层布到
sponson
上衣


Ply sheeting to planing surfaces.

要刨面层薄膜


Anti-trip angles cut and sanded.

防切割和打磨角度行程


Completely sheeted, just requires brass tubes to be epoxied in.

完全铺好，只是需要铜管被
epoxied
英寸


Rear sponsons; same technique as the fronts, just smaller.

后方
sponsons;
作为各条战线同样的技术，只是规模较小

Tub, front and rear sponsons.
浴缸，前方和后方
sponsons

The finished hull, with carbon booms, brass tube mounts and bodyclips retaining sponsons.
368 grams total weight at this point, target weight: 1750 grams ready-to-race.
完成的船体，与碳繁荣，黄铜管坐骑和
bodyclips< br>保留
sponsons
。

三百六十八克此时的总重量，目标重量：一千七百五十克现成的比赛。


Front on.


阵线


Rear sponsons cyano glued to tub.
The last job, a
seam. When this is dry, sand flush.
后方
sponsons
氰基粘浴缸。

最后一个工作，一个
“
带和大括号
”
措施，如果你喜欢，是每个运球沿煤层薄氰基线。

当这
是干的，沙子冲洗

Finishing
To take the boat to a point where it can be run, there is a list of additional tasks to be completed.
The first task is to install the motor mount and drive system. Then, install the rudder and steering
servo. See the article on radio control systems for some tips. If you're going to race the boat you
will need to install an isolation loop.
When you have finished all the tasks that require gluing to the hull, you can go ahead and seal the
boat
using
your
preferred
sealing
product.
I
always
used
to
use
epoxy
laminating
resin
thinned
with isopropyl alchohol. While this does a good job of sealing the wood, it needs a fair bit of work
when cured to get an acceptable surface for painting.
For this boat, I decided to try
CFS Fibreglass Supplies.
Update
Here are some pictures of the finished boat, complete with wire drive, motor etc.
精加工

采取船到了一个它可以运行来看，有一个额外的任务列表来完成。

第一项任务是安装在电
机安装和驱动系统。

然后，
安装伺服舵和方向盘。

上看到的一些小窍门无线电控制系统的
文章。

如果你要去参加比赛的船你将需要安装一个隔离回路。

当您完成所有的任务，需要在船体上胶，你可以继续使用您的密封船密封的首选产品。

我
总是习惯用环氧层压树脂，异丙醇变薄。

虽然这一个密封的木材好，它需 要一个公平的位
工作时治愈得到一个可接受的表面涂装。

对于这样的船，
我 决定尝试
“
四国集团湿印
”
，
我中心购买玻璃纤维制品
（四 国集团与一些稀
释剂）
。

更新

这里有一些船的成品图片，用线驱动器，电机等完成



















Marking Out
Marking out should be done lightly to allow easy removal of any lines afterward. Use a pencil,
steel
rulers
and
an
engineers'
square,
and
take
the
time
to
get
your
marking
out
accurate
-
any
mistakes here will be very difficult to make good later on.
划线

做标记时，应当允许轻轻容易的清除所有行之后。

使用铅笔，尺子和一钢工程师的广场，
花时间让您的标示出准确的

-
任何错误，这里将是非常困难的，好以后



Mark datum lines on the tub floor and transom.

The first job is to mark a longitudinal centreline datum from just forward of the motor mount to
the transom.
If
you elect
to offset the drive in order to counteract propeller torque effects, then
mark
this
offset
drive
line
next.
Mark
the
transom
with
a
driveline
datum
using
an
engineers'
square.
Remove
the
original
centreline
datum
after
you
have
marked
an
offset
datum,
to
avoid
confusion later. Fine-grade sandpaper or dry wet-and-dry paper can be used to scrub out unwanted
lines.
在浴缸地板横梁马克基准线。


第一份工作是为纪念从刚刚电机向前纵向中心线为基准装入横梁。

如果您选择的驱动器，
以便抵消抵消桨扭矩的效果，然后这个偏移车道标志线旁。

马克用传动系统使用的工程师
'
广场基准横梁。

删除原始数据后，你有中心线的偏移标记数据，以避免混乱之后。

细砂纸
或干的湿和干纸可以用来擦洗掉不需要的行。