-
COPRA SILICA
在线硅酸盐分析仪操作手册
ANALYTICAL INSTRUMENTS
Swan Analytical Instruments AG CH-8616 Riedikon / Uster
COPRA Silica
Introduction
_______ __________________________________________________ ________________________
Table of Contents
Important Remarks and Warnings
Installation Checklist
1.1
1.2
1.2.1
1.2.2
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
3
3.1
3.2
4
4.1
4.2
4.3
4.4
4.5
4.5
4.6
5
5.1
5.2
5.3
5.4
5.5
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
Introduction
Principle of Operation
Measuring Principle
On-line Operation
Installation
Onsite Requirements
Sample Requirements
Unpacking
Mounting
Electrical Wiring
Installation of Pressure Bar
Start-up
Display and Keyboard
Display
Keyboard
page
ii
page
iii
page
1.1
page
1.1
1.1
1.2
page
2.1
2.1
2.1
2.1
2.2
2.4
2.11
2.12
page
3.1
3.1
3.2
page
page
page
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.9
5.1
5.2
5.4
5.5
5.8
5.9
6.1
6.1
6.1
6.3
6.4
6.5
6.6
6.7
6.7
6.8
Instrument Set-up / Set-up Mode
Serial Interface (RS232)
Network (RS485)
Printout
Recorders
Measuring of Parameters
Options
Maintenance
Instrument Operation / User Mode
Calibration
Silica Limits
Printer
Logger
Diagnostics
Maintenance
Maintenance Schedule
Changing of Pump Tubes
Mixing of Reagents
Cleaning of Reagent Filters
Maintenance of Solenoid Valve
Changing Tubes on the Photometer
Change of channel selection valve
Start-up after Servicing
Error messages
_________________________________________ ________________________________________
0899
i
COPRA Silica
Introduction
______________________________________________ ___________________________________
Warnings
This instrument conforms to DIN 57411 part 1 / VDE 041 part 1
electronic measuring instruments
this condition and to guarantee harmless operation of the instrument, the user has to observe
all warnings and directives of the manual.
Interruption of the protective grounding line or loosening the ground connection inside or
outside the instrument may lead to dangerous situations. Disconnecting the ground is
prohibited.
Disconnect power whenever electronic service is required. Care should be taken when
opening or removing parts of the instrument; connectors may be under tension. Service
should be performed by authorized personnel only.
If proper operation is not possible any more, the instrument has to be disconnected from all
power lines and measures should be taken to prevent inadvertent operation.
Safe operation is not possible
- if the instrument has been visibly damaged during shipping or installation
- if the instrument does not function
- after extended storage in unfavorable surroundings.
All optionally connected instruments must be approved by IEC 950 / EN 60950 or listed by
UL 1950 or UL 478
Attention:
The instrument can not work without reagents. Reagents can be bought at Swan
respectively your dealer.
Only staff, who knows the procedure and obeys the necessary safety
accommodations (handling of acid respectively poison), is allowed to mix the
reagents.
____________________________________ _____________________________________________
0899
ii
-
-
-
-
-
-
-
-
本文更新与2021-01-24 10:59,由作者提供,不代表本网站立场,转载请注明出处:https://www.bjmy2z.cn/gaokao/560387.html
-
上一篇:青春修炼手册歌词英文
下一篇:中老年微信用户手册 英文