关键词不能为空

当前您在: 主页 > 英语 >

模具翻译

作者:高考题库网
来源:https://www.bjmy2z.cn/gaokao
2021-01-26 03:52
tags:

-

2021年1月26日发(作者:triller)
2


请问此产品的面是否为外观面?表面做什么处理?是晒纹
/
抛光?

Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its

surface? Texture or Polishing?
3


请问产品这个面可否加顶针或顶块?产品允许加扁顶针吗?

Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?
4


这个产品的柱位我们打算做司筒。(或镶针)可以吗?

Can we add ejector sleeves or ejector pins in the boss of this part?
5


产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗?

There's an undercut at this position and it needs a slider. It will also have a
slide split line
on

this side, is that OK?
6


产品里面的这个位置我们打算做斜顶或内行位,有问题吗?

We will make the lifter and (inner) slider in this position, will that be a problem?
9


按你们提供的缩水率千分之五,这个模具的尺寸已经做到了模具图面要 求。但注塑出来的产品不符合
你们的产品图。请确认你们的材料的缩水率是否正确?

Accoring to the shrinkage one over two hundred, the mold has been done in the right dimension, but

the part falls short to your part drawing, are you sure the shrinkage is right?
10


产品的这个位置太小,导致模具钢料太溥,能够加宽这个位置吗?

This position is too small and will make the steel material here too thin, can we widen it here?

11


斜顶与后面的柱位空间太小,斜顶在运动时会干涉到柱子,能移动这个柱子的位置吗?

The angular lifter interferes with the boss during ejection. Please consider changing the position

of the boss.
12


这个筋骨位胶厚太溥,而且高度偏高,注塑时很难填充这个筋位,可以增加这个筋骨位的厚度吗?

The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can
you inrcease the thickness of this rib?
13


你是想将此筋骨位的高度加高
/
减低吗?加胶的位置我们将用铜公放电加深。但减胶的位置有两种做



法,
1
、做镶件;
2
、烧焊;因为镶件的底部有运水,我们简单的做 法是烧焊处理,你可以接受吗?

Will you increase/decrease the material on this rib? We will use EDM if you add material, but there

are two option if you choose to decrease: inserts;g, because there is water in the

bottom of the insert, is that OK?
14


这个样板的筋骨位底部烧焦,是因为排气不良,我们可以在筋骨位的中间增加一个镶件。

This sample has been burned in the bottom because the venting is not good, we can add an insert in

the middle of the rib.
16


产品的这个面我们已经做了晒纹处理,如果需要加胶,
这个 面我们需要重新外发晒纹。可能需要几天
的时间,所以我们直接以铜公放电的火花纹取代你要求的纹路, 你可以接受吗?

We have made the texture on this side, if we add material, it will take some days to remake the

texture by out-resourcing, so we suggest using the texture by EDM instead, is that OK?
18


模具上铭牌上的刻字内容是由你们提供吗?你们什么时候可以这些刻字资料。

Will you provide the engraving content of the plate of this mold to us? When will you send it?
24.
和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動

(The undercut area interferes with the slide block and needs to be filled with material to help the

slider move smoothly.)
28.
滑塊拆的位置

(The split line of slide block or the area of slide.)
29.
此處有尖角,填充困難

(It is hard to fill this area due to the sharp feature.)
30.
此處鋼材太薄,強度不足而且不容易冷卻

(The strength of this area is too weak and it is hard to cool because the steel is too thin.)
31.
圓柱特徵要有一半圓不可以拆在滑塊上,以免粘滑塊造成拉白,拉斷

(We avoid designing the semicircle of the cylinder on the slide block because it will be pulled

apart or cause drag marks.)
32.
此處做斜銷在作動時會削到成品肉厚

(The part will be damaged if we make the lifter in this area.)
33.
這個面是裝配面,不能加料

(This is a critical surface where we cannot add additional material.)
35.
此面是不是外觀面,此處做滑塊的話會有夾線,是否可以接受



have a slide

split line if we have a slide in this area. )
36.
此處有倒勾,能否減料,使公母模靠破,不做滑塊和斜銷



to have shut off
on cavity side. No slide block and lifter will be made. )
39. P.L
面開在此處,模具上會有尖角和刀口,對模具壽命有影響

(There are sharp edges if we set the parting line here, It will reduce the tool life)
40.
加大拔模角,以便脫模順利

We suggest enlarging the draft angle to help release the tool.)

41. GATE
做在此處的話有兩個缺點:
1.
蓋子打開時可以看到
GATE
的修剪部位
; 2.
兩個斜銷在同一側,頂
出也不是

很平衡
.
(There are two problems if the gate is to be designed in this area:
a). It is easy to see the gate mark when you open the cap.
b). The ejectors are unbalanced when two lifters are on the same side)
42. GATE
做在此處 的話
.
蓋子打開後看不到
GATE
的修剪部位

(The gate mark is not visible if the gate position is designed like this.)
43.
如果
GATE
一定要 做在你們指定的位置的話,那還不如做在這一側,這樣的話還可以減小這個位置的
縮水



recommend to have

it to the area indicated so it can avoid a shrink problem in this area.)
44.
在此處
GATE
做潛頂針的話,背後的外觀 面會有沖料痕,而且成品又是黑色的,會最明顯

(If the design of the gate has to be a sub. Gate, then the back surface of the part will have

serious flow marks due to the black colour.)
22. P.L
開在此處不合理,模具加工困難,
P.L
應改為和圖示的一樣



therefore,

we recommend to have the Parting line as indicated.)
45
。产品粘 母模的機會很大,能否在公模加倒勾,拉料頂針或者公模保留
E.D.M
紋,開模時使成品留在 公
模一側



snatch pins
or leave coarse E.D.M. on the core to snatch the part on)

46.
此處料厚段差很大,成品表面會有應力痕,是否接受

(Please confirm whether it is acceptable to have stress lines on the surface because the thickness

is not equal.)
47.
請注明何處為外觀面,能否提供
2D
圖和注意事項

(Please advise where the critical surface is. Please also provide us a 2D drawing with critical

dimensions. )
48.
紅色所示處是有問題的地方,請特別注意

(Please note the red highlights because those areas have problems.)
49.
成品設計此處有問題,建議如下圖所示修改

(We would suggest using the attached part design as the current design has problems.)
50.
此處改為一個球形的凹槽

(We suggest modifying it as a globe recess.)

51.
圓柱特征要有一半不可以拆在滑塊裡,以防拉斷

(this issue is the same as no.8)
52.
此處大滑塊上走小滑塊,小滑塊要先退,大滑塊要做延遲

(The inside small slide block will recede first and the parent slide block have to postpone

sliding.)
53.
滑塊要用液壓油缸抽芯以保証開合模順序

(The slide pins will use an oil cylinder to assure that the process is in proper order.)
54.
這個面有裝配,加料的話裝配時會頂住,如圖所示



assembled.

Please see the sketch attached. )
55.
可降低斜銷面,增加成品些許肉厚來做變化

(To descend the surface of lifter in order to thicken the part.)
56.
一半做斜銷,一半做自然

(One half side will have the lifter and the other half will be

solid/nature.)
57.
此處兩個柱子重疊,有倒勾,不能做自然,要做
SLIDE

suggest making it with a slide block.)
58.
此處強迫頂出

(This area needs force ejection.)
59.
公模兩段開模,這個地方先退

(Here will be a double ejection for forward and receding.)
61.
此面公母模
1
度靠破,會有段差,可否接受

(Please confirm whether it is ok to have mismatch to the area where there is 1 degree of shut off

in Core / Cavity side.)
63.
此處加一個凹槽,膠片的彈出效果會更好一些,試模後看裝配的效果再做修正



assembly parts,

and then make your decision.)
64.
此處有倒勾,建議將剖面線所示部位
CUT
即可避免此處的倒勾

(There is an undercut here, we suggest cutting out the indicated part as it highlighted to avoid an

undercut.)
65.
成型後
SUB GATE
要修平

(The gate (sub gate) needs to be trimmed evenly after being moulded.)
66.
此處倒勾先垂直頂出,之後再手動取出

(This area of the undercut needs to be ejected vertically, then taken out manually.)
67.
這兩個面都有滑塊,
GATE
改在此處改不到

-


-


-


-


-


-


-


-



本文更新与2021-01-26 03:52,由作者提供,不代表本网站立场,转载请注明出处:https://www.bjmy2z.cn/gaokao/569089.html

模具翻译的相关文章